background image

PUSH PRO -0120843

3

Harness attachment points are provided in the platform and the manufacturer recommends the usage of a fall 

restraint harness, especially where required by national safety regulations.
All harness attachment points on SNORKEL vehicles have been tested with a force of 3,650 lbs (16.3 KN)

per person.
See below examples of harness attachment points used on SNORKEL vehicles with their corrosponding rating;

Type 1.

Harness attachment point

 

Type 1.

 

is rated for one lanyard attachment per loop as shown in the 

illustrations depending upon platform occupancy rating 

(see operators manual & decals).

Type 2.

Harness attachment point

 

Type 2.

 

is rated for  two 

lanyard attachments per loop as shown in the 

illustrations depending upon platform occupancy rating 

(see operators manual & decals).

Type 3.

Harness attachment point

 

Type 3.

 

is rated for one 

lanyard attachment per loop as shown in the 

illustrations depending upon platform occupancy rating 

(see operators manual & decals).

Top View

2 lanyard 

attachments

1 lanyard 

attachment

1 lanyard 

attachment

Top View

Front View

Type 4.

Harness attachment point

 

Type 4.

 

is rated for one 

lanyard attachment per loop as shown in the 

illustrations depending upon platform occupancy rating 

(see operators manual & decals).

1 lanyard 

attachment

NOTE:

 There can be more harness attachment points per machine than the 

maximum number of occupants allowed in a platform. Refer to 

the platform decal & specifications table listed in the operators 

manual for the correct occupancy rating before use.

Type 1.

Top View

Top View

2 lanyard 

attachments

Top View

1 lanyard 

attachment

Top View

1 lanyard 

attachment

Summary of Contents for S3006P


























Reviews: