background image

Check all fit 

tings and hoses for leaks. In 

spect

hoses for signs of dam age from chaff ing or rub bing
against pro tru sions on the chas sis.

Care fully in spect the ends of the up per and lower
booms. Leak ing oil can run down the in side of the
booms and drip out the end.

Pay  par tic u lar  at ten tion  to  the  cyl in ders,  check  to
see that there is no oil leak ing from the seal, also
check all hoses that run to the cyl in ders.

Have a qual i fied trained main te nance per son re -
pair all hy drau lic fluid leaks be fore you op er ate an
EPV.

Bolts and Fasteners

Vi su ally in spect all fas ten ers to see that none are
miss ing  or  ob vi ously  loose.

Figure 8.10 - Critical Pin Retainer Bolts

Crit i cal pin re tainer bolts have lock tab wash ers fit -
ted,  they should all be pres ent and not dam aged in
any way. 

Structural Damage & Welds

Figure 8.11 - Structural Damage and Welds

Vi su ally in spect all welds for cracks, all struc tural
mem 

bers for de 

for 

mity, and all sheet metal for

dents that could in ter fere with ma chine op er a tion.

Figure 8.12 - Boom Welds

Pay  par tic u lar  at ten tion  to  the  guard rails.  Make
sure the guard rails are prop erly in stalled, that all
the fas ten ers are in place, and that the swing ing
gate is in place and works properly. 

Lanyard Anchors 

Figure 8.13 - Lanyard Anchors

Vi su ally in spect the lan yard an chor points to see
that they are not de formed, dam aged or cut off.

Bubble Level

Visually check to see that the bubble level is not
damaged, that it is full of fluid, that the bubble does
not exceed the diameter of the center black circle,
and the surface on which the bubble level is
mounted is not deformed or bent out of level. 

Before proceeding with the next section of the
pre-operational inspection you will need to start
the engine and set the stabilisers. Refer to the
Operation Chapter if you need assistance.

page  8 - 4

Rev A

EPV Series – 1596(A)

8. Daily Inspection and Maintenance

Summary of Contents for EPV Series


























































Reviews:

Related manuals for EPV Series