Snell IQBRK3048-2A3 User Instruction Manual Download Page 7 | Manualshive

Page: 7 / 39

background image

IQBRK30

www.snellgroup.com

Introduction

Issue 1 Rev 3

Page 7

©

2013 Snell Limited

1.4 Order Codes

The following product order codes are covered by this manual:

1.5 Rear Panel View

The following rear panel types are available:

IQBRK3048-2A(B)3

IQBRK3049-1A(B)3

Note:

Modules with “A” order codes (for example, IQBRK3048-2

A

3)

can be fitted into either A- or

B-style enclosures. Modules with “B” order codes (for example, IQBRK3048-2

B

3)

can only

be fitted into B-style enclosures. See page 8.

IQBRK3048-2A3
IQBRK3048-2B3

3G/HD/SD-SDI 16-channel AES multiplexer. 2 SDI inputs, 4 SDI outputs,
4 unbalanced AES inputs, 4 unbalanced AES outputs.

IQBRK3049-1A3
IQBRK3049-1B3

3G/HD/SD-SDI 16-channel AES multiplexer. 2 SDI inputs, 2 SDI outputs,
4 balanced AES inputs, 4 balanced AES outputs.

«
...
5
6
7
8
9
...
»

Summary of Contents for IQBRK3048-2A3








































Reviews:

No comments

Related manuals for IQBRK3048-2A3

Brand: Racal Instruments Pages: 63

Brand: IDEAL Pages: 32

Brand: Hioki Pages: 106

Brand: Philex Pages: 2

Brand: Chauvin Arnoux Pages: 64

Brand: Rishabh Pages: 16

Brand: IDEAL Pages: 20

FlexDMM PCI-4070

Brand: National Instruments Pages: 68

Brand: IDEAL INDUSTRIES Pages: 23

Brand: Keysight Pages: 193

Brand: Sifam Tinsley Pages: 18

Brand: UNI-T Pages: 36

Brand: Velleman Pages: 77

Brand: Magnum Pages: 18

Brand: Actron Pages: 2

Brand: METREL Pages: 40

Brand: METREL Pages: 46

Brand: METREL Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands