Snell IQBRK3048-2A3 User Instruction Manual Download Page 13 | Manualshive

Page: 13 / 39

background image

IQBRK30

www.snellgroup.com

Connections

Issue 1 Rev 3

Page 13

©

2013 Snell Limited

3.

Connections

This section describes the physical input and output connections provided by the IQBRK30.

3.1 SDI Inputs

3.2 SDI Outputs

3.3 AES Inputs

3.3.1 Unbalanced – IQBRK3048-2A(B)3

Un

3.4 AES Outputs

3.4.1 Unbalanced – IQBRK3048-2A(B)3

Serial digital input to the unit is made by
means of two BNC connectors which terminate
in 75 Ohms.

Serial digital output from the unit is made by
means of BNC connectors which terminate in
75 Ohms.

•

Four outputs – IQBRK3048-2A(B)3

•

Two outputs – IQBRK30491A(B)3

AES input to the unbalanced unit is made by

means of four BNC connectors, which
terminate in 75 Ohms.

AES output from the unbalanced unit is made

by means of four BNC connectors, which
terminate in 75 Ohms.

«
...
11
12
13
14
15
...
»

Summary of Contents for IQBRK3048-2A3








































Reviews:

No comments

Related manuals for IQBRK3048-2A3

Brand: Agilent Technologies Pages: 4

Brand: Fluke Pages: 26

Brand: VOLTCRAFT Pages: 88

Brand: KRON MEDIDORES Pages: 4

Brand: SONS Online Systems Pages: 11

Brand: Southwire Pages: 7

15190TMaintenancePRO

Brand: Southwire Pages: 33

Brand: Iso-Tech Pages: 4

Brand: Iso-Tech Pages: 32

Brand: HT Pages: 24

Brand: AFi Pages: 8

Brand: AFi Pages: 12

Brand: Velleman Pages: 30

Brand: KPS Pages: 2

Brand: KPS Pages: 2

Brand: KPS Pages: 2

Brand: Perfomance Tool Pages: 16

Brand: Tenma Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands