background image

 

17 

Section 4 - ADJUSTMENTS & REPAIR 

 

WARNING 

Before attempting any adjustments or repairs, STOP 
the engine, remove the spark plug wire from the 
spark plug and secure wire away from plug.  

 
4.3.8.  Replacement Of Bearing On Pulley End Of Hex 
Shaft 
To replace the bearing on the pulley end of the hex 
shaft, proceed as follows: 
1.  Hold the hex shaft with an adjustable wrench 
held next to the pulley. 
2.  Remove the 3/8” hex lock nut which is located at 
the end of the hex shaft on the outside of the right 
wheel bracket.  See Figure 4.17. 
3.  Remove holder, O-ring and bearing. 
4.  Install new bearing. 
5.  Carefully install new O-ring over the outside of the 
new bearing. 
6.  Install bearing holder and secure with screws. 
7.  Install 3/8” hex lock nut. 

 

 

 

FIGURE 4.17 

 
4.4. BELT SERVICE 

On self-propelled mowers, the engine belt transmits 
power from engine to drive disc. The drive disc powers 
the poly-v belt which engages the transmission that 
powers the rear wheels. Should these belts become 
worn, they could cause slippage which would impair 
mower performance. The condition of the engine belt 
and poly-v belt should be checked after every 25 hours 
of mower operation. 
 
 
 
 

4.4.1.  Engine Drive Belt Replacement 
 

(Standard and Stretch Type Belts) 

1.  Empty the fuel tank. 
2. Standard Belt: Unhook the idler spring from the 
right rear wheel bracket. See Figures 4.18. 
2.A. Stretch Belt: Proceed to Step 3. There is no idler 
pulley on these models to disconnect. See Figure 
4.18A. 

 

 

 

FIGURE 4.18 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

TOP VIEW OF ENGINE WITH STRETCH TYPE BELT ROUTING 

 

FIGURE 4.18A 

 
 

(Continued on Next Page) 

 
 
 
 
 
 

BALL BEARING 

“O” RING 

3/8” 
LOCK 
NUT 

BALL 
BEARING 
HOLDER 

RIGHT REAR WHEEL 
BRACKET 

SLOT IN 
DECK 

IDLER 
ARM 

IDLER 
SPRING 

DRIVE DISC 

DRIVE BELT 

ENGINE DRIVE PULLEY 

TOP VIEW OF ENGINE WITH STANDARD TYPE BELT ROUTING 

 

DRIVE DISC 

 

DRIVE BELT 

ENGINE DRIVE 
PULLEY 

Summary of Contents for EMRP215014B






























Reviews: