background image

 

 

15 

Section 4 - REPAIR & ADJUSTMENTS 

 

WARNING 

Before attempting any adjustments, maintenance, 
service, or repairs, stop engine and auger, always 
remove key from ignition switch, remove spark plug 
wire and secure wire away from spark plug. Before 
tilting machine, drain all the fuel from fuel tank. 
Allow engine to run, outdoors where fumes can be 
safely dissipated, until all fuel is removed from 
carburetor. 

 
4.1.2.  AUGER BELT ADJUSTMENT 
 

(IDLER PULLEY ADJUSTMENT) 

 

(Continued From Previous Page) 

4.  Recheck cable for proper extension. 
5.  Reinstall belt cover. 
 
4.1.3.  AUGER BELT REPLACEMENT 
Inspect belt frequently for signs of excessive wear. 
Visually check engine drive belt for cracking, 
fraying, severed or belt strands exposed. NOTE: 
Auger and Drive Belts are difficult to install. It may 
be necessary to allow an authorized Snapper 
Dealer to install these belts.  
1.  
Remove belt cover. See Figure 4.2. 
2.  Remove discharge chute. 
3.  Loosen both auger/impeller belt guides. See 
Figure 4.4. 

IMPORTANT: Wheel  drive belt will have to be removed 
from around engine drive pulley and engine shaft to 
install auger drive belt. 

4.  Remove auger drive belt from around engine 
pulley. See Figure 4.4. 
 
 

 

FIGURE 4.4 

5.  Tilt machine forward to gain access to drive 
system area. Secure machine in the tilted position 
to prevent tipping over. Remove drive system cover 
plate. See Figure 4.5. 

 

 

FIGURE 4.5 

 

6.  Remove auger drive belt from drive disc pulley. 
Route auger belt through drive system in between 
rubber drive tire and drive disc. 
7.  Route new auger drive belt through drive 
system.  NOTE: New belt has to be routed in 
between rubber drive tire and drive disc to position 
it around auger pulley.  
8.  Reinstall wheel drive belt onto engine wheel 
drive pulley. Make sure belt is also positioned in the 
drive disc pulley groove. 
9.  Route auger drive belt around engine auger 
drive pulley. Make sure belt is also positioned in the 
drive disc pulley groove. 
10.  Position both belt guides to have a clearance of 
1/8” from auger drive belt (when engaged) and 
tighten securely.  
11.  Reinstall discharge chute, belt and drive system 
covers and tighten screws securely. 
12.  Reinstall drive system cover plate. 
13.  See Sections 4.1.1. & 4.1.2. Auger Belt 
Adjustment for new belt adjustment. Adjust belt as 
described in these sections. 
 

 
 
 
 
 
 
 
 
 
 

REMOVE DRIVE 
SYSTEM COVER 

LOOSEN 
BELT 
GUIDE 

WHEEL DRIVE 
BELT  

LOOSEN 
BELT GUIDE 

DRIVE DISC 
PULLEY 

AUGER DRIVE BELT 

Summary of Contents for EI55224

























Reviews: