background image

 

IMPORTANT SAFETY INSTRUCTIONS 

 
WARNING: This powerful machine is capable of amputating hands and feet and can throw objects that can cause injury 
and damage! Failure to comply with the following instructions may result in serious injury to the operator or 
other persons. The owner of the snow thrower must understand these instructions and, furthermore, must 
allow only persons who understand these instructions to operate snow thrower. Each person operating the 
snow thrower must be of sound mind and body and must not be under the influence of any substance, which 
might impair vision, dexterity, or judgment. If you have any questions pertaining to your snow thrower which 
your dealer cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER, 
McDonough, Georgia 30253. Phone: 800/935-2967. 
 

PROTECTION FOR CHILDREN 

Tragic accidents can occur if the operator is not alert 
to the presence of children.  Children are often 
attracted to the machine and the snow removal 
activity.  Never assume that the children will remain 
where you last saw them. 
1. 

DO NOT allow children in the area when snow 
thrower is being operated. 

2. 

DO NOT allow pre-teenage children to operate 
snow thrower. 

3. 

ALLOW only responsible adults and teenagers 
with mature judgment to operate the machine 
and then only after being thoroughly instructed 
and under the close supervision of an 
experienced adult operator. 

4. 

Keep the area clear of all persons, particularly 
small children and pets. 

5.  Know how to STOP the snow thrower and 

disengage the controls quickly. 

 

PREPARATION 

1.  Warn everyone in advance to stay clear of area. 

Keep especially watchful for children and pets 
darting into area while operating. 

2.  Read, understand, and follow instructions and 

warnings in this manual and on the machine.  
Know the controls and the proper use of the 
snow thrower before starting. 

3.  Data indicates that operators, age 60 and above, 

are involved in a large percentage of snow 
thrower-related injuries. These operators should 
evaluate their ability to operate the snow thrower 
safely enough to protect themselves and others 
from serious injury. 

4.  Disengage all clutches and shift into neutral 

before starting the engine (motor). 

5.  Wear adequate winter clothing including boots 

which will give you maximum footing on slippery 
surfaces. Exercise CAUTION to avoid slipping or 
falling. 

6.  Before the first snow fall, check the area to be 

cleared and remove all objects such as 
doormats, sticks, toys, wires, rocks, etc., which 
could be hurled or jam the snow thrower. 

 
 
 
 

PREPARATION 

(Continued From Previous Column) 
7.  Survey the area to be cleared beforehand and 

plan where snow is to be blown. Be prepared to 
release auger/impeller clutch or to change 
discharge chute direction quickly to discharge 
away from windows, cars, buildings and 
doorways to avoid property damage or personal 
injury from hurled objects. 

8. Use only approved extension cords and 

receptacles in good condition and with sufficient 
capacity to carry the current to the machine if 
equipped with electric starting motors. 

9.  Handle fuel with extra care.  Fuels are flammable 

and vapors are explosive. Store only in an 
approved fuel container. Never remove fuel cap 
or add fuel with the engine running. Add fuel 
outdoors only with the engine stopped and cool. 
Clean spilled fuel and oil from machine. DO NOT 
smoke. DO NOT run engine indoors. 

 

OPERATIONAL PRECAUTIONS 

1.  Before starting, make visual check to make sure 

auger/impeller housing is clear and all guards 
and shields are in place and tight. 

2.  DO NOT operate machine without proper guards 

shields, deflectors, or other safety protective 
devices in place and functioning properly. 

3. Should the auger/impeller become clogged, 

release the auger/impeller clutch control and, as 
an additional precaution, STOP the engine 
before attempting to unclog the auger/impeller or 
discharge chute. 

4.  DO NOT attempt to unclog the auger/impeller or 

discharge chute by reaching in with your hands.  
Use a  long stick or similar implement to unclog. 

5.  DO NOT attempt to unclog the auger/impeller or 

discharge chute with the engine running. STOP 
engine and remove key. 

6.  STOP engine (motor) and remove key before 

leaving the operator position for any reason. 

 
 
 
 
 
 

 

Summary of Contents for EI55224

























Reviews: