Snap-On MUSCLE MIG SYSTEM MM350XL Owner'S Manual Download Page 6

Page: 6 / 28

SPECIFICATIONS (Cont.)

CHECK LIST

THE SNAP-ON TOOLS MM350XL INCLUDES

THE FOLLOWING:

1- Combination Power Source/Remote

Feed Unit.

1- Dual Cylinder Rack & Industrial

Wheel Kit.

1- FCA-15X 15 foot Feeder Control

Cable assy.

1- 35XL12 12 foot MIG Torch with

adjustable nozzle.

1- 20CP-3M 20 foot Power Input

Cable.

1- SN-178X521 25 foot Work Cable

and 500 amp clamp.

1- 350LPK Parts Kit.
1- GR-FM Gas Regulator/Flowmeter.
1- ER70S-6-35-3, Sample Spool of

.035 Steel Wire.

1- 8IN-A 8 inch Reel Adapter.

ITEMS REQUIRED FOR MIG WELDING

WHICH ARE NOT PROVIDED WITH THE

MM350XL

1. Full cover welding helmet with

proper colored lens (shade 9 to
11 depending on operator’s pref-
erence).

2. Proper shielding gas and cylin-

der.

3. Leather welding gloves.

4. Electrical power and matching

electrical plug.

THE MM350XL REQUIRES A 208
OR 230 VOLT, SINGLE PHASE,
AC, 60 AMP CIRCUIT

5. Other personal protective

equipment which may vary to
match the welding being per-
formed.

WIRE TYPES:

mild steel,

stainless steel, aluminum,

bronze, flux cored,

flux cored - gasless

Recommended (for steel)

ER70S-6

WIRE SIZES:

.023" - 1/16" steel,

3/64 - 1/16" aluminum,

(.023" - 3/64" alum. w/spool gun)

.030" - .035" bronze,

.035" - .045" flux cored

(gas shielded or gasless)

Recommended Size: Aluminum

.035

Others

.035

SHIELDING GASES:
For Steel

CO2 or Argon/CO2 mix

Recommended (for steel) 75% Argon/

25% CO2

For Aluminum, Bronze

100% Argon

For Stainless Steel

98% Argon/2% Oxygen

For Flux cored

CO2 or

Argon/CO2 mix

DIMENSIONS:
Height

35-3/4 in.(90.8 cm.)

Width

27-1/4 in.(69.2 cm.)

Depth

34-1/2 in.(87.7 cm.)

Weight

275 lbs.(124.9 kg.)

TORCH SPECIFICATIONS

NECK ANGLE:

60 degrees

LEAD LENGTH:

12 feet

OVERALL LENGTH:

12 feet

COOLING METHOD:

gas (air)

RATING - DUTY CYCLE:
With Argon/CO2 gas

250 amps @ 100%

With CO2 gas

300 amps @ 100%

Summary of Contents for MUSCLE MIG SYSTEM MM350XL





























Search results

Summary of Contents for MUSCLE MIG SYSTEM MM350XL

Reviews:

Related manuals for MUSCLE MIG SYSTEM MM350XL

Brands by name

Popular brands

Snap-On MUSCLE MIG SYSTEM MM350XL, Owner'S Manual

Search results

Summary of Contents for MUSCLE MIG SYSTEM MM350XL

Reviews:

Related manuals for MUSCLE MIG SYSTEM MM350XL

Brands by name

Popular brands