SMK P100AC Operator'S Safety And Service Manual Download Page 4

or works with this equipment is familiar with all safety 
precautions. 

!

   

 

W A R N I N G

 

 

!

 

GENERAL WARNING:  Indicates information important to 
the proper operation of the equipment. Failure to observe 
may result in damage to the equipment and/ or severe 
bodily injury or death. 

!

   

 

C A U T I O N

   

 

!

 

GENERAL CAUTION:  Indicates information important to 
the proper operation of the equipment. Failure to observe 
may result in damage to the equipment. 

REFERENCES:  For details on safety rules and regulations in the United States, contact 
your local Occupational Safety and Health Administration (OSHA) office. Equipment 
operated in other countries must be operated and serviced in accordance and 
compliance with any an all safety requirements of that country. The publication of these 

safety precautions is done for your information. SMK does not by the publication of these 

precautions imply or in any way represent that these are the

 

sum of

 all dangers present 

n

ear

 

SMK equipment. If you are operating SMK equipment, it is your responsibility to 

insure that such operation is in full accordance with all applicable safety requirements 
and codes. All requirements of the United States Federal Occupational Safety and 
Health Administration Act must be met when operated in areas that are under the 
jurisdiction of the United States Department. 

  

Page 2 

Safety Precautions 

!

   

 

W A R N I N G

 

 

!

 

Before attempting to operate the unit, read and 
understand all safety precautions and warnings. 

Do not use the unit when tired, ill, or under the 
influence of alcohol, drugs or medication. 

Inspect unit before each use for loose, broken, 
cracked, split, or damaged parts. Do Not operate the 
unit with loose or damaged component parts. 

Always wear safety glasses or goggles that are 
marked with ANSI Z87 

Use only in daylight or good artificial light. 

Never use unit without the proper factory authorized 
accessories attached. When using the unit, ensure 
that the sprayer discharge hose is securely 
attached. 

Do not modify the unit 

Page 3 

Trouble shooting 

Troubleshooting

Replacement Parts

Summary of Contents for P100AC










Reviews: