Smithy Midas 1220 XL Operator'S Manual Download

Page: 61 / 115

Figure11.21 With the slot for the #1 jaw in the 12:00 position, the slot for the #2 jaw is at 8:00

and the slot for the #3 jaw is at 4:00.

Collets and Collet Attachments

To hold small-diameter work, whether bar stock fed through the hole in the spindle or

small pieces of semi finished parts, collet attachments are preferable to standard chucks

(Figure 11.22) for several reasons:

• They have much faster release and grip actions.

• They center the work automatically and accurately

• They grip even small pieces and pieces with a short hold firmly.

Figure 11.22 Collet attachments are best for small-diameter work.

• They are housed within the spindle nose for maximum tool clearance, making it

possible to machine, thread, or cut off close to the spindle.

While chucks are universal tools that hold a range of stock sizes and shapes, collets are

special tools. There is a collet for every size and shape of workpiece.

Made with extreme accuracy, hardened, and ground, standard split collets are slotted so

their jaw ends compress inwardly to grip the workpiece. This is done by pulling the

collet jaw's externally tapered shoulder into a matching taper-bored adapter sleeve. The

adapter sleeve connects the lathe spindles MT5 taper to the collets MT3 taper. A drawbar

holds the collet in place.

Slot #1

Slot #2

Slot #3

11-11

Or Visit www.smithy.com

Setting Up with Centers, Collets, and Chucks

Summary of Contents for Midas 1220 XL




















































































































Search results

Summary of Contents for Midas 1220 XL

Reviews:

Related manuals for Midas 1220 XL

Brands by name

Popular brands

Smithy Midas 1220 XL, Operator'S Manual

Search results

Summary of Contents for Midas 1220 XL

Reviews:

Related manuals for Midas 1220 XL

Brands by name

Popular brands