Smiths Medical CADD 2120 Technical Manual Download Page 26

Page: 26 / 40

leanIng

Cleaning Procedures

Cleaning Solutions

The following solutions may be used to clean the pump and accessories, unless otherwise specified:

•

Soap solution

•

Benzalkonium chloride concentrate (0.13%)

•

Glutaral concentrate, USP (2%)

•

10% solution of household bleach

(1 part household bleach to 9 parts water)

•

Alcohol, USP (93%)

•

Isopropyl alcohol, USP (99%)

•

Chlorhexidine gluconate (4%)

•

PDI Super Sani-Cloth

•

Madacide (MADA Medical)

•

Virex II (Johnson Wax)

•

Coverage Spray and Coverage HB Plus (Steris)

•

CaviCide

(Metrex)

•

Quik Fill Compac (A-456-N) (Airkem)

Cleaning the Pump and Accessories

WARNING:

Ensure that debris is not allowed to build up on the pressure plate surface of the pumping

mechanism. Inspect the air detector sensor slot and remove any debris. A blocked air detector

sensor may not detect air present in the fluid path, which could result in serious patient injury

or death.

CAUTION:

•

Do not immerse the pump in cleaning fluid or water. Do not allow solution to soak into the pump,

accumulate on the keypad, or enter the battery compartment, USB port, remote dose cord jack, or

power jack areas. Moisture buildup inside the pump may damage the pump.

•

Do not clean the pump with acetone, other plastic solvents, or abrasive cleaners, as damage to the

pump may occur.

Note:

Refer to the instructions for use for each accessory before proceeding with cleaning.

1. Dampen a soft, lint-free cloth with cleaning solution. Apply the solution to the exterior surface of the

pump or accessory according to manufacturer’s instructions.

Do not allow the solution to soak into the

pump or accessory.

2. Allow the pump to dry completely before use.

Summary of Contents for CADD 2120









































Search results

Summary of Contents for CADD 2120

Reviews:

Related manuals for CADD 2120

Brands by name

Popular brands

Smiths Medical CADD 2120, Technical Manual

Search results

Summary of Contents for CADD 2120

Reviews:

Related manuals for CADD 2120

Brands by name

Popular brands