background image

Table of Contents

3304 Service Manual 

i

Revision History  ................................................................v
Warranty & Service Information .....................................vii

Proprietary Notice ............................................................................................... vii
Warranty ................................................................................................................. vii

Limited Warranty ......................................................................................... vii
Disclaimer of Warranties .......................................................................... viii
Conditions of Warranty ............................................................................ viii
Limitation of Remedies ............................................................................ viii
Warranty Procedure .....................................................................................ix

CE Notice ..................................................................................................................ix

Chapter 1: Introduction ................................................ 1-1

About this Manual ..............................................................................................1-1
Symbol Definitions .............................................................................................1-1
Warnings ................................................................................................................1-3
Cautions .................................................................................................................1-8
Notes .......................................................................................................................1-8

Chapter 2: Oximeter Circuit Description ..................... 2-1

Functional Structure ..........................................................................................2-1
Battery Charger ...................................................................................................2-1

General Description ..................................................................................2-1

Oximeter On/Off Control .................................................................................2-2
System Power Supply ........................................................................................2-2
Microprocessor Circuit ......................................................................................2-2

Reset Circuit .................................................................................................2-3
Memory and I/O Decoding ....................................................................2-3
Dual microprocessor operation ............................................................2-3

Interface Circuit ...................................................................................................2-4

Addressable Latch and Speaker Output ............................................2-4

Table of Contents

Summary of Contents for BCI 3304





































Reviews: