Smith SPS10 Operation - Repair - Parts Download Page 66

Page: 66 / 68

All written and visual data contained in this document reflects the latest product information available at the time of publication.

SMITH reserves the right to make changes at any time without notice.

Original instructions.

This manual contains English. MM 3A5578

SMITH Surface-Prep Solutions

2504 NW 19 Street

Pompano Beach, FL 33069

www.SMITHmfg.com

Revision

June 2019

SMITH SPS10 DCS
Noise level (dBa)

Sound power

109 dBa per ISO 3744

Sound pressure

94 dBa measured at 3.1 feet (1m)

Vibration level*

Right/Left Hand

13.5 m/sec

* Vibration measured per ISO 5349 based on 8 hr daily exposure

Dimensions/Weight (unpackaged)

Metric

Height (handle up)

53 in.

135 cm

Height (handle down)

42 in.

107 cm

Length

38 in.

97 cm

Width

20 in.

51 cm

Weight

263 lb

119 kg

WARNING:

This product can expose you to chemicals known to the State of California to cause cancer

and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

CALIFORNIA PROPOSITION 65

Summary of Contents for SPS10





































































Search results

Summary of Contents for SPS10

Reviews:

Related manuals for SPS10

Brands by name

Popular brands

Smith SPS10, Operation - Repair - Parts

Search results

Summary of Contents for SPS10

Reviews:

Related manuals for SPS10

Brands by name

Popular brands