manualshive.com logo in svg

Smith-Root LR-24, User Manual, Page: 47 / 62

Share
Download
Smith-Root LR-24 User Manual Download Page 47

44

www.smith-root.com

LR-24

BACKPACK ELECTROFISHER

lithium batteries). 
Trickle charging optimizes battery shelf life by reducing 
cell deterioration.  Keeping batteries fully charged can 
greatly increase battery life.  The MC-24 eliminates the 
hassle of shuffling batteries from shelf to charger and 
keeps batteries properly charged and ready for service.  
With the built-in battery evaluation load test function 
and maximum charge indicators, you can see the state 
of charge and condition of each battery and identify low 
charged and worn-out batteries.  Charging batteries using 
the MC-24 takes between two and four days.  It is also an 
excellent cost effective alternative to purchasing multiple 
battery chargers because it can recharge four batteries at 
once.

BAT-01 BATTERY ANALYSIS TOOL

The Battery Analysis Tool (sold separately) operates in 
conjunction with the UBC-24 Battery Charger (

Fig. 6.5

).  It 

tests all models (lead-acid and lithium) of 24V backpack 
batteries and in a clear and concise manner gives the 
usable battery life remaining.
This tool is not to be used during each charge/discharge 
cycle, but rather is intended to be used a few times a year, 
just prior to actually using the batteries.  It may also be 
used to accurately test any Smith-Root 24 Volt battery 
where the battery condition is either unknown or is 
questionable. 
In practice, the Battery Analysis Tool is plugged into a 
standard Smith-Root UBC-24 and also the battery under 
test (use provided adapter for lithium batteries).  The 
battery will begin to charge as soon as the charger is 
plugged in (Do not use an MC-24 Maintenance Charger for 
this test).  

SECTION 6: BATTERY MAINTENANCE & DIAGNOSTIC EQUIPMENT

MC-24 Maintenance Charger

BAT-01 Battery Analysis Tool

Fig. 6.5 BAT-01 Battery Analysis 

Tool

MC-24 MAINTENANCE CHARGER

The Smith-Root MC-24 Maintenance Charger (sold 
separately) is specifically designed for lead-acid battery 
maintenance and storage (not intended for use with 

MC-24 Maintenance Charger ....................... 06811

BAT-01 Battery Analysis Tool ....................... 08041

UBC Charger

AC

BAT-01

Battery

Summary of Contents for LR-24































































Reviews:

No comments