background image

 

 

 

 

 

EN 

1

12 

Activated Charcoal Filter (Recirculation Version) 

This cannot be washed or regenerated, and must be changed when 

G

 starts to flash, or at least 

once every 4 months. The Alarm signal, if it has been activated, only appears when the Suction 
motor is turned on.

 

Activating the alarm signal  

•  In Recirculation Version Hoods, the Filter Saturation Alarm must be activated on installa-

tion or at a later date. 

•  Turn the Lights and the Suction Motor off. 
• Press 

and

 

hold for approximately 5 seconds: 

• 

Button

 

flashes twice -- A.C. Filter saturation alarm 

ACTIVATED

 

• 

Button

 

flashes once -- A.C. Filter saturation alarm 

DEACTIVATED

 

CHANGING THE ACTIVATED CHARCOAL FILTER 

Resetting the alarm signal 

•  Turn the Lights and the Suction Motor off. 
• Press button 

G

 and hold for approximately 5 seconds (See 

paragraph on Use). 

Changing the Filter 

•  Remove the Metal grease filters. 
•  Remove the Suction Panel by unfastening the 4 screws at the 

corners. 

•  Remove the saturated Activated charcoal filter, using the hooks 

provided. 

•  Fit the new Filter, hooking it into place. 
•  Replace the Panel and the Metal grease filters. 

 

 

 

 

 

Summary of Contents for SHW1235X

















Reviews: