background image

 

 

Instructions for the user

 

 

32

 

8. CLEANING AND MAINTENANCE

 

 

 

 

Before any intervention, disconnect the power supply of the device.

 

8.1 Cleaning

 

 

 

 

 

Clean the cooking top regularly every time you use it, obviously after it 
has cooled. 

 

8.1.1  Regular daily cleaning of the hob 

In order to clean and preserve the surface, always use specific products 

only

, which do not contain abrasive substances or chlorine-based acid 

substances. 

How to use:

 pour the product on a damp cloth and wipe the surface, 

rinse thoroughly and dry with a soft cloth or deerskin. 

 

8.1.2  Food stains or residues 

Do not use metallic sponges or sharp scrapers: they will 
damage the surface. 
Use normal non-abrasive products and remove spots or 
residuals with non-scratch sponges or, if need be, with wood or 
plastic utensils. 
Rinse thoroughly and dry with a soft cloth or deerskin. 

 

8.2 Cleaning of cooking hob components

 

Grids, caps, flame cap crowns and burners can be 
removed for ease of cleaning. Wash them in warm 
water using a non-abrasive detergent, taking care 
to remove all tough spots. Before remounting, allow 
the components 

to fully dry out

 

8.2.1  Ignition plugs and safety devices 

For good functioning of the lighting ignition plugs and the safety devices, 
keep them very clean. 
Check frequently and clean with a damp cloth when necessary. 

 

Summary of Contents for ER 17250


















Reviews: