SMC Networks SMCWEB-N2 User Manual Download Page 18

Page: 18 / 148

SMCWEB-N2 Wireless N Universal Repeater User Manual

- 18 -

Chapter 10.: Web
Configuration for the WDS
Mode

Describes how to use to Web page to
configure parameters for the WDS mode.

Chapter 11.: Web
Configuration for the Client
Mode

Describes how to use to Web page to
configure parameters for the Client mode.

Features



Support IEEE802.11b, IEEE802.11g, IEEE802.11n, IEEE802.3, IEEE802.3u,

IEEE802.11i, and IEEE802.11e



Provide wireless transmission rate up to 300 Mbps



Support WEP and WPA for secure data transmission



Support DHCP server



Support manually configuring static routing



Support software upgrade through Web pages



Support restoring factory default settings



Support demilitarized zone (DMZ)



Support DNS proxy and forwarding



Support

UPnP



Support

WPS



Support port forwarding



Support port triggering



Support wireless repeater



Support guest network



Support filtering by keyword and domain name



Support wireless security authentication



Support 5 types of WAN connection modes, including static IP, dynamic IP,

PPPoE, PPTP and L2TP



Support remote access control



Support

firewall



Support system status display



Support backing up and restoring configuration files

Summary of Contents for SMCWEB-N2





















































































































































Search results

Summary of Contents for SMCWEB-N2

Reviews:

Related manuals for SMCWEB-N2

Brands by name

Popular brands

SMC Networks SMCWEB-N2, User Manual

Search results

Summary of Contents for SMCWEB-N2

Reviews:

Related manuals for SMCWEB-N2

Brands by name

Popular brands