SMC Networks SMC7904WBRA-N2 User Manual Download

Page: 124 / 127

User Manual

120

In this page, you can view the statistical information about the recevied and
transmitted data packets of the xDSL interfaces.
Click

xDSL BER Test

to test the xDSL Bit Error Rate.

Click

Reset Statistics

to restore the values to zero and recount them.

10.4.8 Route

Choose

Device Info

Route

and the following page appears.

In this page, you can view the route table information.

10.4.9 ARP

Choose

Device Info >

ARP

and the following page appears.

In this page, you can view the MAC address and IP address information of the device
connected to the router.

10.4.10 DHCP

Choose

Device Info >

DHCP

and the following page appears.

Summary of Contents for SMC7904WBRA-N2
































































































































Search results

Summary of Contents for SMC7904WBRA-N2

Reviews:

Related manuals for SMC7904WBRA-N2

Brands by name

Popular brands

SMC Networks SMC7904WBRA-N2, User Manual

Search results

Summary of Contents for SMC7904WBRA-N2

Reviews:

Related manuals for SMC7904WBRA-N2

Brands by name

Popular brands