SMC Networks SMC7904WBRA-N2 User Manual Download

Page: 99 / 127

User Manual

In this page, you can enable or disable writing operation from WAN or LAN side. After
proper configuration, click

Apply/Save

to apply the settings.

10.2.13 Interface Grouping

Choose

Advanced Setup > Interface Grouping

and the following page appears.

Interface grouping supports multiple ports to PVC and bridging groups. Each group
will perform as an independent network. To support this feature, you must create
mapping groups with the appropriate LAN and WAN interfaces using the

Add

button.

The

Remove

button will remove the grouping and add the ungrouped interfaces to

the default group. Only the default group has IP interface.

Summary of Contents for SMC7904WBRA-N2
































































































































Search results

Summary of Contents for SMC7904WBRA-N2

Reviews:

Related manuals for SMC7904WBRA-N2

Brands by name

Popular brands

SMC Networks SMC7904WBRA-N2, User Manual

Search results

Summary of Contents for SMC7904WBRA-N2

Reviews:

Related manuals for SMC7904WBRA-N2

Brands by name

Popular brands