Hexagon socket head cap screw
(M2.5 x 9 L)
Hexagon socket head cap screw
(M2.5 x 6 L)
Protrusion
Auto switch mounting bracket
Protrusion
Hexagon socket head cap screw
(M2.5 x 9 L)
Hexagon socket head cap screw
(M2.5 x 6 L)
Auto switch mounting bracket
BMG5-025S
Note)
BQ3-032S
Note)
Note) When the auto switch
mounting bracket is
ordered by its part
number, it includes the
bracket and screws in the
dashed line.
Note) When the auto switch
mounting bracket is
ordered by its part
number, it includes the
bracket and screws in the
dashed line.
Mounting and Moving Method of Auto Switch
Direct Mounting to the Round Groove
Mounting and Moving Method of D-P3DW
(1)
q
Insert the protrusion on the bottom of the auto switch into the mat-
ing part of the auto switch mounting bracket and fix the auto switch
and the auto switch mounting bracket temporarily by tightening the
hexagon socket head cap screw (M2.5 x 9 L) 1 to 2 turns.
w
Insert the temporarily tightened mounting bracket into the mat-
ing groove of the cylinder/actuator, and slide the auto switch
onto the cylinder/actuator through the groove.
e
Check the detecting position of the auto switch and fix the
auto switch firmly with the hexagon socket head cap screw
(M2.5 x 6 L, M2.5 x 9 L).
∗
r
If the detecting position is changed, go back to step
w
.
∗
The hexagon socket head cap screw (M2.5 x 6 L) is used to fix the
mounting bracket and cylinder/actuator.
This enables the replacement of the auto switch without adjusting the
auto switch position.
Note 1) Ensure that the auto switch is covered with the mating groove to
protect the auto switch.
Note 2) The torque for tightening the hexagon socket head cap screw
(M2.5 x 6 L, M2.5 x 9 L) is 0.2 to 0.3 N·m.
Note 3) Tighten the hexagon socket head cap screws evenly.
Applicable cylinder/actuator
Auto switch
mounting bracket
part no.
BQ3-032S
Compact cylinder
Compact cylinder with lock
Pin clamp cylinder
Pin clamp cylinder with lock
CDQS
CDQ2
CDLQ
CKQG
CLKQG
ø
25
ø
32 to
ø
100
ø
25 to
ø
100
ø
50
ø
50
Direct Mounting to the Square Groove
Mounting and Moving Method of D-P3DW
(2)
q
Insert the protrusion on the bottom of the auto switch into the mat-
ing part of the auto switch mounting bracket and fix the auto switch
and the auto switch mounting bracket temporarily by tightening the
hexagon socket head cap screw (M2.5 x 9 L) 1 to 2 turns.
w
Insert the temporarily tightened mounting bracket into the mat-
ing groove of the cylinder/actuator, and slide the auto switch
onto the cyinder/actuator through the groove.
e
Check the detecting position of the auto switch and fix the
auto switch firmly with the hexagon socket head cap screw
(M2.5 x 6 L, M2.5 x 9 L).
∗
r
If the detecting position is changed, go back to step
w
.
∗
The hexagon socket head cap screw (M2.5 x 6 L) is used to fix the
mounting bracket and cylinder/actuator.
This enables the replacement of the auto switch without adjusting the
auto switch position.
Note 1) Ensure that the auto switch is covered with the mating groove to
protect the auto switch.
Note 2) The torque for tightening the hexagon socket head cap screw
(M2.5 x 6 L, M2.5 x 9 L) is 0.2 to 0.3 N·m.
Note 3) Tighten the hexagon socket head cap screws evenly.
Applicable cylinder/actuator
Compact guide cylinder
Compact guide cylinder with lock
MGP
MGPS
MLGP
ø
25 to
ø
100
ø
50
,
ø
80
ø
25 to
ø
100
Caution for the Cylinder/Actuator Mounting
∗
When mounting the D-P3DW onto a cylinder/actuator with ø32
to ø50, to avoid mutual interference, use a fitting with width
across flats 12 mm or less for ø32 and ø40, and use a fitting
with width across flats 14 mm or less for ø50. Also, if the corner
of the fitting interferes with the housing of the auto switch,
adjust the tightening of the fitting to eliminate the interference.
In the case of interference with an elbow type fitting, direct the
port of the fitting away from the auto switch. Such interference
must be avoided especially when a speed controller and speed
exhaust controller with a fitting are selected.
∗
In the CDQSø25 and CDLQø25, the auto switch will interfere
with the fitting if mounted onto the face with the port, so it
needs to be mounted on a different face.
Note) For the MGP end lock type, as the auto switch cannot be mounted
onto the lock mechanism face, mount it to the groove on the bottom
of the lock mechanism face.
Note) When the auto switch is mounted onto the CDBQ2 end lock type,
please contact SMC.
Auto switch
mounting bracket
part no.
BMG5-025S
7
Series
D-P3DW
S20-201A-D-P3DW.qxd 10.1.28 10:59 AM Page 5
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
