SMC Networks 7204BRB User Manual Download Page 27

Page: 27 / 89

Configuration

MAC Spoofing

The MAC Spoofing is developed to solve the scenario when the ISP
only recognizes one MAC address. Copy the ISP-recognized MAC
address here.

ATM

[Service Category] [UBR] and [CBR] are supported from the ATM.
[Bandwidth]

Bandwidth setting takes effect only when the CBR
is selected.
The maximum available bandwidth is from the
upstream data rate of [ADSL Status] page.

Encapsulation, Bridge, PPP and DHCP Client

Use the following table to configure a valid setting for each PVC.

WAN
Configuration

Bridge
Mode

Router Mode
(PPPoA /
PPPoE)

Router Mode

(Dynamic IP)

Router
Mode
(Static IP)

IP address

N/A

Automatically
assigned by ISP

Provided
by ISP

Subnet Mask

N/A

Automatically
assigned by ISP

Provided
by ISP

Gateway

N/A

Automatically
assigned by ISP

Provided
by ISP

Encapsulation

1483 Bridged
IP LLC, 1483
Bridged IP
VC-Mux

PPPoA LLC/
VC-Mux, PPPoE
LLC/VC-Mux

1483 Bridged/
Routed IP LLC,
1483 Bridged
Routed
VC-Mux,
Classical IP
over ATM

1483 Bridged/
Routed IP
LLC, 1483
Bridged
Routed
VC-Mux,
Classical IP
over ATM

Bridge

Enabled

Disabled

PPP Service

N/A

Provided
by ISP

N/A

PPP
User name

N/A

Provided
by ISP

N/A

Summary of Contents for 7204BRB


























































































Search results

Summary of Contents for 7204BRB

Reviews:

Brands by name

Popular brands

SMC Networks 7204BRB, User Manual

Search results

Summary of Contents for 7204BRB

Reviews:

Brands by name

Popular brands