background image

 

 

fig.3

 

ASSEMBLE DOOR

 

7

 

SELECT:

 

 

2 x 1.940 m  Door Sheets (Narrow)

 

2 x 0.945 m  Door Top/Bottom Flashings

 

2 x 1.940 m Door Side Flashings

 

3 x Hinges

 

1 x Padbolt Support Flashing

 

2 x 1.200 m  Door Brace Flashings

 

59 x Rivets

 

STEP 1:

 

 

• 

Lay out door sheets on a flat surface 

making sure narrow pans are on the 

outside.

 

 

• 

Rivet sheets together in the centre en-

suring ends are flush with each other.

 

STEP 2:

 

 

• 

Position door side flashings and top 

and bottom flashings and assemble 

door as shown, ensuring narrow 

face of flashing is on the front as 

per fig.1

 

 

 

STEP 4:

 

 

• 

On the back of the door, place door braces in posi-

tion as shown in 

fig.4.

 

 

• 

Ensure that the top and bottom ends of the braces 

are under the door flashings as shown in 

fig.5 

and 

opposite ends of the braces overlap in the middle.

 

 

• 

Rivet door brace flashings onto back of door as 

shown. Where possible, rivet from front of door

.

 

STEP 3:

 

 

• 

Attach hinges to door side flashing using rivets provided. 

Ensure hinge is flush with back of door, and 60mm in from 

each end as per 

fig.2.

 

 

• 

Using six rivets, attach padbolt support as shown in 

fig. 3.

 

NARROW PANS

 

fig.2

 

fig.4

 

fig.5

 

Hinges

 

fig.1

 

Summary of Contents for SM1515

















Reviews: