background image

                                       

 

HEM4000 Engine Controller User Manual                                                                                      Page 35 of 46 

No.   

Type   

Description 

20 

Water Gun On-Off Status 

Normal  status:  if  input  is  active,  bypass  control  outputs 
from start idle time to stop idle time; 
Idle running status: if input is active, engine goes from idle 
running to normal working status, and meanwhile bypass 
control outputs (if configured). 

21 

Alarm Stop Inhibit 

All  shutdown  alarms  are  inhibited  except  for  emergency 
stop and over speed shutdown. (Override Mode) 

22 

Instrument Mode 

All outputs are inhibited in this mode. 

23 

Reserved 

 

24 

Reset Maintenance Time 

Maintenance 1’s time and date is set as preset value when 
input is active. 

25 

External Charging Failure 

When input is active, charging failure alarms happen. 

26 

High Temp. Shutdown 

Connect sensor digital input. 

27 

Low OP Shutdown 

Connect to sensor digital input. 

28 

Remote Start 

In

 Auto

 mode, when input is active, engine can be started 

automatically.   

29 

Remote Stop 

In 

Auto 

mode, when input is active and remote start input 

is inactive, engine can be stopped automatically.   

30 

High Level Input 

In 

Auto 

mode, when input is active, engine can be started 

automatically (drain flood). 

31 

Low Level Input 

In 

Auto 

mode, when input is active and high level input is 

inactive,  engine  can  be  stopped  automatically  (drain 
flood). 

32 

Manual Start Input 

In 

Auto 

mode, when input is active, engine can be started 

automatically;  when  input  is  inactive,  engine  can  be 
stopped automatically. 

33 

Reserved 

 

34 

Simulate Stop key 

Connect  an  external  button  (unlatched)  and  press 
simulate panel buttons. 

35 

Simulate Manual key 

36 

Simulate Auto key 

37 

Simulate Start key 

38 

Simulate  Speed  Adjustment 
Key 

39-51 

Reserved 

 

52 

Speed Raise 

Connect an external button (unlatched) and control speed 
manually. 

53 

Speed Drop 

Summary of Contents for HEM4000















































Reviews: