EZUIRT Universal IR/Insteon/X10 Transceiver
#5010H
Your EZUIRT is a multi-functional device that brings the versatility of
Insteon and X10 to the coffee table through commonly available infra-red
(IR) remote controllers. The device allows control of anything connected
to an Insteon or X10 network with the same remotes used with audio-
visual/entertainment equipment. As an IR X10 transceiver, your EZUIRT
receives and decodes all 256 X10 addresses from an IR remote and sends
them over the power line. In Insteon mode, any IR X10 address or IR code
can be set up to send Insteon group commands or status change
broadcast messages to control single or multiple Insteon devices in a
scene. EZUIRT is also an IR sender, capable of converting Insteon
commands to IR codes (singularly or as macros) that your A/V equipment
can readily understand.
The built-in IR receiver can be bypassed with an external one (included)
allowing ultimate placement flexibility. EZUIRT can also function as an IR
repeater or distribution box (IR blaster) sending the IR signals received
through 4 separate jacks that accommodate up to 8 IR emitters (not
included.)
Setting Up EZUIRT With a Remote as an Insteon or X10 Controller
EZUIRT receives IR X10 codes and sends them on the power line, emulating the IR543 or IR543H. In Insteon mode, the
unit associates an IR code (X10, NEC, RC5 or SONY) with a group number from 1 to 40. Multiple devices can be set up
on the same group thus enabling a single IR command to control multiple Insteon units in a scene. EZUIRT can
alternatively be made to send an Insteon broadcast message (instead of a group command) upon receiving the IR
code. This mode is useful with some software applications.
Controlling Insteon Devices with IR X10 Codes:
When linked to Insteon devices using X10 IR codes, EZUIRT will send Insteon ON, OFF, BRIGHT and DIM group commands upon
detection of corresponding X10 commands. It is only necessary to link the X10 ON button of the controller as follows:
1. Press and hold the pushbutton on the side of EZUIRT for about 10 seconds, at which point its LED will flash about
once per second (slow rate) indicating EZUIRT is listening for an IR code.
2. On the IR remote press the X10 ON button to be used for control. The LED on the side of the EZUIRT will flash
more rapidly when it “learns” the IR signal—EZUIRT is now in Insteon linking mode.
3. To link one or several Insteon devices to this code, press the pushbutton on the Insteon device to be controlled
until its LED (or the load connected to it) flashes indicating a successful link (3-4 seconds.) The LED on the EZUIRT
will continue blinking as it stays in linking mode ready to accept additional devices.
4. If no additional devices need to be linked, end the linking process by pressing the pushbutton on the EZUIRT for
about 4 seconds. The LED on the EZUIRT will glow steadily.
Controlling Insteon Devices with IR Codes Other than X10:
When using IR codes other than X10, it is necessary to tell the EZUIRT the desired Insteon command to be sent, as outlined below.
1. Press and hold the pushbutton on the side of EZUIRT for about 10 seconds. Its LED will flash about once per
second (slow rate) indicating EZUIRT is listening for an IR code.
2. On the IR remote press the button to be used for control. The LED on the side of the
EZUIRT will flash more rapidly when it “sees” the IR signal—EZUIRT is now in linking mode.
3. To link one or several Insteon devices to this code, press the pushbutton on the Insteon
device to be controlled until its LED (or the load connected to it) flashes indicating a
successful link. The LED on the EZUIRT will continue blinking as it stays in linking mode
ready to accept additional devices.
4. If no additional devices need to be linked, end the linking process by pressing the
pushbutton on the EZUIRT for about 4 seconds. The LED on the EZUIRT will turn off.
5. We now tell EZUIRT, via taps on its pushbutton, which Insteon command to send. Tap the
pushbutton (according to Table 1 on the right) a number of times corresponding to the
desired command to be sent upon receiving this code.
6. Now end the linking process by pressing the pushbutton on the EZUIRT for about 4
seconds. Its LED will glow steadily again.
1-949-429-3303
smartenit.com
© 2015 Compacta International, Ltd.
EZUIRT and Smar tenit ar e tr ademar ks of Compacta Inter national Ltd.
Rev 2—3/2015; Applies to firmware 2.8 and above
Insteon is a trademark of SmartLabs, Inc. and the Insteon networking technology is covered by pending U.S. and foreign patents.
Table 1
# of Taps Insteon
Command
1
On
2
Off
3
Toggle
4
Not Used
5
Bright
6
Dim
Installation
Select a suitable power outlet anywhere in your Insteon power line network close to where the IR remotes will be
operated. The built-in IR receiver is on the lower front of the unit and must be in the line of sight of the controlling
remote for best results. Optionally, the unit may be placed behind a cabinet, and the IR signal brought to it by either
an external receiver or an IR repeating emitter placed next to the built-in receiver. For convenience, a pass-through
outlet is provided. Avoid exposure to moisture.
External IR
Receiver
Push Button
and LED
Built-in IR
Receiver
IR Signal
LED
