background image

Longo Modbus Products LMP-1.MP2

4 OPERATION

Basic settings can be entered with panel Touch Buttons (TB).
Modes of operation and parameters can be set from any Modbus RTU Master.

It is advised to press touch-buttons respectively with finger not faster than 1 press per second.

Press should be done with whole finger tip. Brief pressing could not activate the action, because of 
protection against the noise and other influence. 

4.1 Operational modes

LCD Display “stand-by mode”

The display is normally in this mode, if no TB is pressed in last ~5 seconds. 

LED intensity is in correlation with Light intensity measurement (more light - brighter, less light - 
darker).

Actual room temperature (0.5 °C resolution) is shown on the screen if enabled.

LCD Display “SET mode”

First press on any TB will activate the display to “set mode” and LCD intensity will be put to 
maximum. No action regarding the pressed TB is done. Further pressings on any TB will make the 
change (bar-graphs) regarding the pressed TB. 

Actual temperature set-point (regarding the right bar-graph) is shown on the screen if enabled.

Display will return to “stand-by mode” if touch buttons are not pressed for a while (~5 seconds). 

Changing operation modes

Request for switching between CP 

normal

 and 

economic

 operating mode  is done with lower left and

right TB pressed simultaneously : switch to 

economic

 mode

Request for switching between CP 

on

 and 

off

 operating mode  is done with upper

 

left and right TB 

pressed simultaneously : CP switched 

off

 

Confirmation of above requested modes is done by Modbus RTU Master equipment by changing the 
appropriate command bit (normal/economic, system on/off).  

Normal

This is default mode for MP2 module. The control algorithm is executing regarding the parameters.

Economy

If set, controller will start cooling when room temperature will raise above max. temperature set- 
point (SP) and stop when temperature will drop 1 °C below max. temp. SP. On the other hand, when
room temperature fall's below min. temp. SP controller will start heating and stop when 
temperature will raise 1 °C above min. temp. SP.
In economic mode “ECO” sign appear on LCD.

Off

In this mode panel sends command to switch off all devices: hot valve and cold valve. Temperature 
LCD bar becomes white and “OFF” sign appear on LCD.
CP can be turned off using 

System On/Off

 command. In this case cool, heat commands are switched 

off. Cool and heat commands are also switched off when temperature measured by the panel is 
inside temperature dead band values (default dead band is 0.5 °C).

    

   

3

Summary of Contents for LMP-1.MP2
























Reviews: