manualshive.com logo in svg

SMART Board MX (V2) Series, Installation And Maintenance Manual

Share
Download
SMART Board MX (V2) Series Installation And Maintenance Manual Download Page 71

APPENDIX B

MANAGING THE DISPLAY USING RS-232

61

smarttech.com/kb/171555

Power states

The display has six power states:

Power state

Description

ON

The display is in normal operating mode.

READY

The screen is off, but the display is ready to turn on when the following
occurs:

l

A user presses the

Power

button

on the convenience panel or the

remote control.

l

You send the

set powerstate=on

command.

STANDBY

The screen is off, and the display is in a low power state. The display enters
READY or ON state when the following occurs:

l

A user presses the

Power

button

on the front control panel or the

remote control.

l

You send the

set powerstate=standby

command.

POWERSAVE

The screen is off, and the display is a very low power state. The display
enters READY or ON state when the following occurs:

l

A user presses the

Power

button

on the front control panel or the

remote control.

l

You send the

set powerstate=powersave

command.

UPDATEON

The display is updating firmware. Do not turn off the display.

UPDATEREADY

The display is updating firmware while the screen is off. Do not turn off the
display.

With the exception of

get powerstate

and

set powerstate

, commands are available only when

the display is in READY or ON power state.

Commands and responses

To access display information or to adjust display settings using the room control system, type

commands after the command prompt (>) and wait for the response from the display.

CORRECT

>get volume
volume=55
>

Summary of Contents for Board MX (V2) Series

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands