manualshive.com logo in svg

SMART Board MX (V2) Series, Installation And Maintenance Manual

Share
Download
SMART Board MX (V2) Series Installation And Maintenance Manual Download Page 29

CHAPTER 2

INSTALLING THE DISPLAY

19

smarttech.com/kb/171555

Connecting power and turning on the display for
the first time

The final step in installing and configuring the display is to connect power and turn it on. When you

first turn on the display, a setup wizard appears. Follow the steps in the wizard to complete the

setup of the display.

To connect the display to power

Connect the supplied

power cable

from the AC power inlet on the back of the display to a

power outlet.

SBID-MX265-V2

SBID-MX275-V2

SBID-MX286-V2

NOTE

Refer to the display’s specifications for power requirements and power consumption

information (see

More information

on page 8).

To turn on and set up the display for the first time

IMPORTANT

Install the OPS PC before you turn the display on.

NOTES

l

Touch is not available right after waking up the display or turning it on. Wait a few seconds

and then the display will respond to touch.

l

If a USB drive connected to the display’s service port, do not remove the USB drive. The

USB drive contains an important firmware update.

Summary of Contents for Board MX (V2) Series

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands