background image

Legal Restrictions

SMA

 

Technologie AG

Page 4

SB1700-11:SE2006

Installation Guide

Liability exclusion

The information contained in this documentation are the property of 

SMA

 Technologie AG. No part of this

documentation may be published without written permission from 

SMA

 Technologie AG. A reproduction for

internal purposes for the evaluation of the product or an appropriate application is permitted and does not
require authorization. 
All information are based on our "General Terms and Conditions of Delivery of 

SMA

 Technologie AG”.

The content of this documentation is reviewed continuously and adjusted, if necessary. 

SMA

 Technologie

AG provides this documentation without exclusion of deviations and without warranty of completeness. You
will find the current version on the Internet at 

www.SMA.de

 or can obtain it via the usual sales channels.

Warranty or liability claims for all kinds are excluded in case of damages due to:
• Inappropriate use of the product
• Operation of the product in an improper environment
• Operation of the product without considering the relevant safety regulations 
• Non-fulfillment of the warnings or safety instructions described in the documentation for the product
• Operation of the product under faulty conditions concerning security and protection
• Arbitrary changing of the product or the provided software
• Failure of the product due to interference of connected or contiguous devices out of legal limit values
• Disasters and force majeure

Software Licensing

The use of the provided software by 

SMA

 Technologie AG is subject to the following conditions:

The software may be reproduced for internal purposes and installed on any number of computers. Provided
source codes can be changed and adjusted on the company’s own authority according to the internal
purpose. Driver may be ported to other operating systems as well. No part of the source codes may be
published without written permission of 

SMA

 Technologie AG. Sublicensing of the software is not

acceptable.
Liability limitation: 

SMA

 Technologie AG disclaims liability for any direct or indirect consequential damages

arising from the use of the software produced by 

SMA

 Technologie AG. The same applies for the provision

and/or non-provision of support.
Provided software not produced by 

SMA

 Technologie AG is subject to the respective licensing and liability

agreements of the manufacturer.

Trademarks

All brand and product names used herein are trademarks or registered trademarks of their respective
holders, although they may not be specifically designated as such.

SMA

 Technologie AG

Hannoversche Strasse 1-5
34266 Niestetal
Germany
Tel. (+49) 5 61 95 22 – 0
Fax (+49) 5 61 95 22 – 100

www.SMA.de

E-Mail: [email protected]

© 2005 

SMA

 Technologie AG. All rights reserved.

Summary of Contents for SUNNY BOY 1700

















































Reviews: