manualshive.com logo in svg

Sleipner SE-IP30, Installation Manual, Page: 2 / 28

Share
Download
Sleipner SE-IP30 Installation Manual Download Page 2

2

5453

11

2021

-

SE IP 30 s2 & SE IP 40 s2 

     

Sleipner Motor AS

P.O. Box 519, Arne Svendsensgt. 6-8

N-1612 Fredrikstad, Norway 

MC_0020

Contents

Products 

SE40/125S2-12IP - SE40 Tunnel thruster, 12v-IP 

SE30/125S2-12IP - SE30 Tunnel thruster, 12v-IP  

Installation Manual 

Responsibility of the installer ...................................................................................................................................................................3

 

Thruster Measurements   ....................................................................................................................................................................... 4 

Thruster Specifications

 ........................................................................................................................................................................... 5 

Technical Specifications  

 ....................................................................................................................................................................... 5 

Positioning of the tunnel / thruster .......................................................................................................................................................... 6 

Tunnel Length ......................................................................................................................................................................................... 7 

Tunnel installation in sail boats ............................................................................................................................................................... 8 

Water Deflection

 ..................................................................................................................................................................................... 9 

Tunnel ends .......................................................................................................................................................................................... 10 

Tunnel installation ..........................................................................................................................................................................  11 - 12 

Stern tunnel installation ........................................................................................................................................................................ 13 

Gear Leg & Motor Bracket Installation.................................................................................................................................................. 14 

Propeller Installation ............................................................................................................................................................................. 15 

Motor Installation .................................................................................................................................................................................. 16 

Thruster Electrical Installation .............................................................................................................................................................. 17 

Electrical Specifications 

 ....................................................................................................................................................................... 18 

Technical Wiring Diagram  .................................................................................................................................................................... 19 

Control Panel Cable Installation  .......................................................................................................................................................... 20 

Visual Wiring Diagram ...........................................................................................................................................................................21 

Control Panel Installation ..................................................................................................................................................................... 22 

 

Pre-delivery Checklist  .......................................................................................................................................................................... 23

 

Service and Support........................................................................................................................................................................... 24

Product Spare Parts and Additional Resources .............................................................................................................................. 24

Warranty Statement ............................................................................................................................................................................ 24

Summary of Contents for SE-IP30





























Reviews:

No comments