manualshive.com logo in svg

Sleipner PHC-3, User Manual, Page: 22 / 32

Share
Download
Sleipner PHC-3 User Manual Download Page 22

22

5267

15

2022

-

PHC-3

SLEIPNER AS

P.O. Box 519
N-1612  Fredrikstad
Norway
www.sleipnergroup.com

DOCUMENT ID:

REVISION:

DATE:

LANGUAGE:

Installation Guide

When installing an S-Link™ system DO NOT connect any other control equipment directly to the S-Link™ bus except original Sleipner S-Link™ products. 

In case of connecting third-party equipment, it must always be connected through a Sleipner-supplied interface product. 

Any attempt to directly control or connect into the S-Link™ control system without a designated and approved interface will render all warranties and 

responsibilities of all of the connected Sleipner products. 

If you are interfacing the S-Link™ bus by agreement with Sleipner through a designated Sleipner supplied interface, you are still required to install at 

least one original Sleipner control panel to enable efficient troubleshooting if necessary.

MC_0105

The installer must read this document to ensure necessary familiarity with the product before installation. 

Instructions in this document cannot be guaranteed to comply with all international and national regulations. It is the responsibility of the 

installer to follow all applicable international and national regulations when installing Sleipner products. 

The recommendations given in this document are guidelines ONLY, and Sleipner strongly recommends that advice is obtained from a person 

familiar with the particular vessel and applicable regulations.

This document contains general installation instructions intended to support experienced installers. If you are not skilled in this type of work, 

please contact professional installers for assistance.

If required by local regulation, electrical work must be done by a licensed professional.

Appropriate health and safety procedures must be followed during installation.

Faulty installation of Sleipner products will render all warranties given by Sleipner Motor AS.

MC_0038

Responsibility of the Installer

MG_0485

1

2

Tank sensor 

cable

(Black) X3 

S-Link cable 

X5 

Power colling 

pump cable

(Blue) X1 

Hydraulic colling 

pump cable

(Grey) X2 

Thruster 

valve cable

(White) X4 

System 

pressure cable

X6 

Stabilizer 

powerpack cable

X7 

Summary of Contents for PHC-3

































Reviews:

No comments