Skyworth KEB001Z2470 Service Manual Download Page 48 | Manualshive

Page: 48 / 74

background image

46

Troubleshooting

Diagram 2:

Main test points:

● Is the temperature of Indoor and Outdoor Unit too high?
● Is the fan of Indoor and Outdoor Unit operating normal?
● Is the radiating of Indoor and Outdoor Unit well(Including the fan speed is lower or not )?
● Is the pipe temperature sensor normal?

Overload Anti-high

temperature protection

Is the outdoor unit environment

temperature over the 53

℃

or not?

Normal protection,please

improve the indoor and

outdoor unit temperature

environment before use

Improve the heat radiation

environment of unit.

Indoor and outdoor unit

heat radiating is poor.

Indoor and outdoor

motor work well.

1. Checking the fan terminals

connect well or not?

2. Checking the motor of

Indoor and Outdoor Unit

is well or not?

Change the motor capacity C1

Checking the pipe temperature sensor is

normal or not comparing pipe temperature

sensor resistance table(Checking the

temperature of out pip while cooling

checking the temperature of inside pip)

Check the pipe temperature

sensor work well.

Change the relevant

pipe temperature

sensor

End

Replace the corresponding control board

(changed the outdoor control board during

cooling, changed the indoor control board

Cut the power wait for 20 mins

Change outdoor

motor

Y

«
...
46
47
48
49
50
...
»

Summary of Contents for KEB001Z2470











































































Reviews:

No comments

Related manuals for KEB001Z2470

Brand: York Pages: 44

Brand: Haier Pages: 22

Brand: Haier Group Pages: 28

Brand: Daikin Pages: 6

Brand: Daikin Pages: 72

Brand: Daikin Pages: 20

Brand: Daikin Pages: 44

Appliances AHM24DPH1

Brand: GE Pages: 1

Brand: Panasonic Pages: 108

Brand: NewAir Pages: 106

Brand: Daikin Pages: 28

Brand: Friedrich Pages: 28

Brand: Sakura Pages: 20

Brand: Danby Pages: 80

Brand: Carrier Pages: 54

Brand: Parker Pages: 48

Brand: Daikin Pages: 24

Brand: Daikin Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands