background image

4

27

Installation instruction

Make sure the temperature of the places where the washer is installed 
or placed above 0

 

or put it outside.

Place the washer correctly according to management standards and 
regulations.
Keep the base of washer ventilated when it is placed on the ground
 with carpet.
There are too much pests in villages. Please keep the surroundings 
clean because any damages caused by cockroaches or other pests 
don't belong to warranty.

Transport bolt

   

Washers are installed with transport bolt to prevent internal damage 

   in transit.

Dismantle the transport bolt

1.In order to prevent internal damage in transit, 4 bolts are installed. 
   Before using the washer, dismantle the bolt.(see chart I )
   If the bolts are not dismantled, violent vibration, noise and trouble 
   will be caused.
2.Use the attached wrench to loosen the 4 bolts. (see chart 2)
3.Twist the bolt rubber slightly and then pull out the bolts, keep the 
   bolts and wrench as standby.(see chart 3)
   The bolts should be remounted no matter when to transport the washer.
4.Use attached stopples to seal the screw holes. (see chart 4)

see chart 1

see chart 2

see chart 3

see chart 4

Notice

 

please don't 
dismantle the 
drainpipe fixed 
device.

the plug 
of trans
portation 
bolt

3

.

Notes

When put big and small clothes together, put the big first and they 
have to be less than half of total clothes. Please don't wash single 
cloth because it may cause the trouble of imbalance. 
Please add one or two similar clothes.
Small clothes like silk stockings and handkerchiefs should be put 
into mesh bags to wash. Before washing the bra with steel rings, 
please take the rings off. If it is inconvenient to do this, please put 
them into mesh bags to prevent the bra slipping into the gap between 
internal and external tubs.
Check all pockets and make sure nothing in them. Nails, hairpin, 
match, pen, coin and key will damage your washer and clothes.
Zip up all clothes, fix the button and hook and tie the loose belt, 
make sure that other clothes cannot be damaged by them.
Firstly use the water with a little detergent to wash the parts with too
many stains, such as collar and cuffs, which can make the clothes 
cleaner.
Check the door seals and make sure nothing on them.
Make sure there is nothing in the tub before washing.
Please use the low bubble detergent specially for front loading 
washing to wash the cloths.

Summary of Contents for F701202ND

















Reviews: