background image

- 06 -

WARNING AND SAFETY NOTES  

These warnings and safety notes are particularly important. 
Please follow the instructions for maximum safety; otherwise the 
charger and the battery can be damaged or at worst it can cause 
a fire.

WARNING AND SAFETY NOTES  

Never leave the charger unattended when it is connected to its 
power supply. If any malfunction is found, Terminate THE 
PROCESS AT ONCE and refer to the operation manual.

Keep the charger well away from dust, damp, rain, heat, direct 
sunshine and vibration. Never drop it.

The allowable input voltage is 11-18V DC/110-240V AC.

This charger and the battery should be put on a heat-resistant, 
noninflammable and nonconductive surface. Never place them 
on a car seat, carpet or similar. Keep all the inflammable 
volatile materials away from operating area.

Make sure you know the specifications of the battery to be 
charged or discharged to ensure it meets the requirements of 
this charger.  If the program is set up incorrectly, the battery 
and charger may be damaged .It can cause fire or explosion 
due to overcharging. This warranty is not valid for any damage 
or subsequent damage arising as a result of a misuse or failure 
to observe the procedures outlined in this manual. 

Summary of Contents for e6680





























Reviews: