4. INSTALLATION
The motion sensor should be installed at a location where you want to
monitor movement, so when movement is detected at this location, the
light will be on. You should mount it at a height of 7ft from the ground.
Walk test should be performed after the motion sensor is mounted. Walk
in the detected area, if motion is detected, a red light inside the sensor
will glow. If the red light does not glow, motion has not been detected and
you may need to re-position the sensor. Ensure you walk test all the
locations that you would like the motion sensor to cover.
Note:
- Perform the walk test after you
have inserted the battery for more
than 1 minute.
- Before performing the walk test,
the sensor should not detect any
motion.
- After motion is detected once,
the sensor will not be triggered
unless no motion is detected for
3 seconds. Therefore, wait for
at least 3 seconds during walk
testing between 2 activations.
Caution:
When installing the motion sensor, avoid placing it near heat or cold
producing devices (i.e. A/C or furnace vents, fans, ovens, space heaters,
etc). Air movement, especially caused by changes in temperature may
trigger the Motion Sensor and cause false alarms. Please carefully test
your Motion Sensor so that it will only be triggered by wanted movement.
TM
M
0
1
2
3
4
5
6
7
8
9
10
2
4
6
8
10
DETECTING AREA: (Unit = meter)
55°
22°
22°
12°
SENSOR
27°
55°
1.2M
11°
After walk testing, you may power up the lighting receiver module. When
motion is detected, the red LED on the front of the motion sensor will flash
and the light connected to the receiver module should also be on.
If the light at the receiver module is not on, but the red LED on the motion
sensor flashes, please ensure you have the correct setting of the CDS
Light Sensor, i.e. if you enable CDS Light Sensor and you are testing this
at a bright environment, the light connected to the motion sensor will not
be on. If the CDS Light Sensor setting is correct, please ensure the
motion sensor is programmed to the lighting receiver module. If you are
not certain if the motion sensor is properly programmed, you can program
it again.
5. TESTING AND OPERATION
Walk Test
7. FCC
The Remote Control is approved by the FCC and it complies with Part 15 of the
FCC Rules. Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible
of compliance could void the user’s authority to operate the equipment.
8. CUSTOMER SERVICE
If you would like to order Skylink’s products or have difficulty getting them to work
or download latest information and user manual, please :
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at [email protected], or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com
P/N. 101A396
Patent Pending
©2010 SKYLINK GROUP
9. ACCESSORIES
The Skylink
Lighting System consists of many other devices from
multiple button transmitters, Motion Sensor, various receivers such as
Wall Switch Receiver, Plug-in Receiver with Repeater, Outdoor Receiver,
Dimmer Module etc. Please visit Skylink website at www.skylinkhome.com
for more information.
TM
Home
If the connector is in place, the
light sensor threshold is set at a
lower brightness value, i.e. a
motion activation signal will not
turn on the lighting receiver unless
the environment is really dark.
If the connector is removed, the light
sensor threshold is set at a higher
brightness value, i.e. a motion
activation signal will turn on the
lighting receiver even the environ-
ment is not so dark.
You should set the desired light sensing threshold by trial and error.
After setting all the jumper connectors, you may place the battery com-
partment door back on and tighten the screw. You may now mount the
motion sensor at the desired location where movement will be monitored.
3. CUSTOMIZING THE MOTION SENSOR (CONT)
7ft
6. ERASING MOTION SENSOR
You may erase a transmitter from the receiver module, but you cannot
erase a specific device, you must erase all the wireless devices, then
program the ones you want to keep. Follow the instructions below to
erase programmed transmitters.
1. Power off the lighting receiver module.
2. Press the SET button on the Motion Sensor.
3. Press and hold the programmed number button on the transmitter for
at least 2 seconds. Do not release this button until step 5.
4. Power up the lighting receiver module, you will hear beeping and the
light will be on.
5. You may release the button on the transmitter.
6. When the button is release, the light connected to the receiver module
will be off, indicating you have successfully erased all the devices
from the lighting receiver.
Erasing Motion Sensor from the Dimmable Receiver Module
model MD-318 or On / Off Receiver Module model MR-318
