manualshive.com logo in svg

Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2, User Manual, Page: 24 / 56

Share
Download
Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2 User Manual Download Page 24

4O3A Signature – Antenna Genius User Manual

 

Index

 

 

 

Page 

23

 of 

55

 

 

BCD, or Pin-to-Port) to AG.

 

You can change DIP settings for band data sources while the device is powered on but it’s not 
recommended if you have any RF cables connected to your switch.

 

 

9.1.2. Download and install the latest AG Windows App

 

 

The AG Windows App has been tested to run on Windows 7, 8.1 and 10, both Pro and Home 
and both 32 and 64-bit editions, and is available free from the Downloads page on 4O3A.com:

 

 

 

Download the AG Windows App to your PC’s Downloads folder. You may see a warning message 
from your browser or security software for trying to download a Windows executable file (.exe 
file), you may override this warning if you are confident you have downloaded the file from 
4O3A.com.

 

 

Select the installation language from the pull-down menu and select 

OK

.

 

 

 

 

 

 

After closing all other applications, launch the Setup Wizard by selecting 

Next

:

 

 

Summary of Contents for 4O3A Signature Antenna Genius 8x2 Plus v2

























































Reviews:

No comments