5
GB
Digital angle finder
0580
INTRODUCTION
• This measuring tool is intended for digitally measuring
and defi ning angles from 0° to 220° (horizontal and
vertical)
• Read this instruction manual carefully before use and
save it for future reference
2
TECHNICAL SPECIFICATIONS
Material
aluminium
Measuring range
0° - 220°
Measuring accuracy
- angle
+/- 0.5°
- bubble level
1 mm/m
Lowest indication unit
0.1°
Power supply
1x 6LR61/9V battery
Estimated battery life
20 hours
Operating temperature
-10°C to 50°C
Storage temperature
-20ºC to 70°C
Automatic switch-off
after approx. 5 min. of inactivity
Length
380 mm
Weight
0,18 kg
TOOL ELEMENTS
1
A On/off button
B “HOLD” button for retaining measured values
C LCD display
D Bubble level for horizontal planes
E Bubble level for vertical planes
F Base leg
G Fold-out leg with 32 cm ruler
H Battery compartment cover
J Low battery level indicator
K Retain mode (“HOLD”) indicator
USE
• Mounting of battery
3
- use exclusively alkaline-manganese or rechargeable
batteries
- remove cover H
- insert 9V battery (pay attention to correct
polarisation)
- mount
cover
H
- when battery level is low, symbol J
1
will appear in
display
- when
symbol
J
1
appears in the display for the fi rst
time, measuring is still possible but with reduced
accuracy; replace the battery
- always remove the battery from the tool, if the tool
will not be used for a long period
• On/off
- switch on/off the tool by pressing “On/Off” button A
1
- after approximately 5 minutes without button
actuation or angle change, the measuring tool
automatically switches off to preserve battery life
• Measuring angles
4
! protect the measuring tool against impact and
shock (dropping or banging the tool may lead to
faulty measurements)
! keep the contact edges of the measuring tool
clean (debris particles may lead to faulty
measurements)
- position base leg F
1
and fold-out leg G
1
against
the edges to be measured
- the reading in display C
1
corresponds with angle X
and remains unchanged until the legs are moved
! when directly projecting a measured angle onto a
workpiece, pay attention that base leg F and fold-
out leg G are not moved and that the retaining
(“HOLD”) mode is not switched on
• Retaining measured values
- the current reading can be retained in display C
1
by
pressing “HOLD” button B
1
(symbol K
1
will
appear in display)
- the reading remains unchanged (even when the legs
are moved) until “HOLD” button B is pressed again
! be aware that the retaining mode also
automatically switches off after 5 minutes of
inactivity
APPLICATION ADVICE
• Use “HOLD” button B
1
for defi ning angles at hard-to-
reach and/or dark places where measuring and reading
cannot take place simultaneously
• Use bubble level D
1
or E
1
for defi ning angles when
only one reference point is available
5
GUARANTEE / ENVIRONMENT
• Always keep the measuring tool free of dust, moisture
and direct sunlight
• Clean the tool with a dry, soft cloth (do not use cleaning
agents or solvents)
• Always store the tool indoors in its protective carton/
case
• Do not disassemble or modify the tool in any way
• This SKIL product is guaranteed in accordance with
statutory/country-specifi c regulations; damage due to
normal wear and tear, overload or improper handling will
be excluded from the guarantee
• In case of a complaint, send the tool undismantled
together with proof of purchase to your dealer or the
nearest SKIL service-station (addresses are listed on
www.skileurope.com)
SKIL_IB0580db.indd 5
SKIL_IB0580db.indd 5
30-05-2007 13:07:33
30-05-2007 13:07:33
Та
ше
в
-
Га
лв
ин
г
ОО
Д
www.tashev-galving.com
