background image

YOU MUST FILL OUT YOUR WARRANTY REGISTRATION 

TO ACTIVATE YOUR WARRANTY AND TO QUALIFY FOR 

PARTS AND SERVICE!!

To the Owner;

Thank-You for choosing a quality product from Pequea Machine, Inc. We 

strive to give you the best equipment and the best level of service of any 

company. With a little care and maintenance this machine will do your work 

for you for many years. In this manual, we make an effort to get you better 

acquainted with the machine so you can achieve maximum performance. We 

design and build all of our equipment with the end user in mind so we wel-

come any suggestions or ideas for improvement. Please note that it is within 

our rights to make changes or improvements to our equipment without updat-

ing the equipment that was manufactured before the change took place.

Please take a few minutes to fill out the area below. This information will be 

valuable to you when ordering parts or requesting service from your dealer. 

Dealer Name:_____________________________

Dealer Phone Number:______________________

Service Manager/Technician:_________________

Model# and Description:_____________________

Serial Number:____________________________

Date of Purchase:__________________________

Summary of Contents for PEQUEA CX551



















Reviews: