background image

13

Pequea Machine’s Limited Warranty

Pequea Machine Company warrants to the original Purchaser all Machinery, Equipment, or Trailers manufactured 

by it, to be free from defects in material and workmanship under normal use and service. Its obligation under this 

Warranty shall be limited to replacement or repair of any parts thereof, free of charge to the original Purchaser, 

at its place of business, provided, however, that the part(s) to be replaced or repaired, shall within one (1) year 

after delivery to the original Purchaser, be demonstrated to be defective; which determination shall be made by 

the Company. The said components or parts must be returned through the Selling dealer or distributor directly 

to the Company with all transportation charges prepaid. Notice of defect shall be furnished in writing to the 

Seller and to the agent through whom the machinery was received, disclosing in full all known defects and 

failure in operation and use, and reasonable time shall be given to the Seller to remedy any such defects and 

failures. Failure to make such trial or give such notice shall be deemed an absolute acceptance by the Buyer 
and satisfaction in full of this Limited Warranty.

This Warranty does not cover, under any circumstances, any parts, components, or materials which, in the 

opinion of the Seller and Company, have been subjected to neglect, misuse, alteration, accident, or if repaired, 
with parts other than those manufactured by and obtained from Pequea Machine Company.

This Warranty does not cover components which are already covered by a separate Warranty provided by the 
supplier of said parts or components.

The Company’s obligation under this Warranty is limited to repair or replacement, free of charge to the original 

Purchaser, of any part which in judgment of the Company is defective. This Warranty does not cover normal 
wear and tear.

THIS WARRANTY IS MADE EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, 

INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR USE AND PURPOSE AND OF 

ALL OTHER OBLIGATIONS OR LIABILITIES ON ITS PART AND ANY IMPLIED WARRANTY. AND IT NEITHER 

ASSUMES NOR AUTHORIZES ANY OTHER LIABILITY IN CONNECTION WITH A SALE OF THIS MACHINE. THIS 

WARRANTY SHALL NOT APPLY TO THIS MACHINE OR TO ANY PART THEREOF WHICH HAS BEEN SUBJECT 
TO ACCIDENT, NEGLIGENCE, ALTERATION, ABUSE, OR MISUSE.

The Company makes no Warranty whatsoever in respect to accessories or parts not supplied by the Company. 

The term “original Purchaser” as used in this warranty, shall be deemed that person for whom the Machine, 

Equipment, or Trailer is originally supplied. This Warranty shall apply only within the boundaries of the 
continental United States.

Under this Warranty, the Company cannot guarantee that existing conditions beyond its control will not affect 
its ability to obtain materials or manufacture necessary replacement parts.

No one is authorized to alter, modify, or change the terms of this Warranty in any manner.

The Company warrants the Construction of the equipment sold herein and will replace at its expense for a 

period of (1) year from the date hereof, any parts which prove defective as determined under the terms of this 
Limited Warranty.

WARRANTY

Summary of Contents for PEQUEA CX551



















Reviews: