SKC 220-4000 Operating Instructions Manual Download Page 1

Page: 1 / 34

skcinc.com

Form 37171 Rev 200630

Page 1

AirChek Connect Sample Pump

Cat. No. 220-4000
Operating Instructions

Figure 1. AirChek

Connect Overview

Table of Contents

Introduction ................................................................................................................................................ 3

Checking Pump Kit/Contents .................................................................................................................... 3

Getting Started ........................................................................................................................................... 4

Charging the Battery Pack......................................................................................................................... 4

Notes and Cautions ................................................................................................................................... 5

Turning Pump Power On/Off ..................................................................................................................... 5

Interpreting the Display .............................................................................................................................. 6

Determining Battery Charge Status ........................................................................................................... 6

Using the Touch Screen ............................................................................................................................ 7

Navigating Menus and Screens ................................................................................................................ 7

Determining Pump Status.......................................................................................................................... 9

Modifying Device Settings ......................................................................................................................... 9

Operation ................................................................................................................................................. 16

Protective screen cover

On/off button

Belt clip in back

(not shown

)

Charging

contacts

Battery pack

Front and side view

Top view

Inlet
housing/filter

Touch screen/display

LED Indicator

Summary of Contents for 220-4000



































Search results

Summary of Contents for 220-4000

Reviews:

Related manuals for 220-4000

Brands by name

Popular brands

SKC 220-4000, Operating Instructions Manual

Search results

Summary of Contents for 220-4000

Reviews:

Related manuals for 220-4000

Brands by name

Popular brands