Sitecom KAMULTSSVDA User Manual Download Page 16 | Manualshive

Page: 16 / 65

background image

Sitecom Wireless Network UMTS Router 54G WL-610

16

5.2.2 Device Status

View the Broadband router’s current configuration settings. The Device Status displays the

configuration settings you’ve configured in the

Wizard / Basic Settings / Wireless

Settings

section.

Parameters

Description

Device Status

This page displays the Broadband router LAN port’s current LAN

IP Address

and

Subnet Mask

. It also shows whether the

DHCP Server

function is enabled/disabled.

«
...
14
15
16
17
18
...
»

Summary of Contents for KAMULTSSVDA


































































Reviews:

No comments

Related manuals for KAMULTSSVDA

Brand: Paradyne Pages: 11

Brand: Paradyne Pages: 19

Brand: Paradyne Pages: 32

COMSPHERE 3550 Series

Brand: Paradyne Pages: 153

Jetstream CPX-1000

Brand: Paradyne Pages: 141

FrameSaver 9783

Brand: Paradyne Pages: 28

COMSPHERE 6800 Series

Brand: Paradyne Pages: 7

SMART NODE 4950-NCE

Brand: Patton electronics Pages: 8

NetLink 2960 RAS

Brand: Patton electronics Pages: 2

Brand: Patton electronics Pages: 2

Brand: Qlogic Pages: 20

LightSpeed Appliance QLS250

Brand: Quantum Pages: 12

NVIP- NVRA0104/GO

Brand: Novus Pages: 44

Brand: Kramer Pages: 2

Brand: Maipu Pages: 26

Brand: Comtrend Corporation Pages: 4

Brand: Linksys Pages: 6

Brand: MaxComm Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands