7
rugs or carpets over it. The appliance can be
fitted to a purpose made proprietary class
“O” – 100°C or 150°C surround.
2.9
In particular the finished hearth level
MUST
extend 300mm in front of the vertical face of
the fireplace for both the 16” and 18”
variants. The minimum width of the hearth is
650mm for the 16” and 700mm for the 18”
version.
THE APPLIANCE MUST NOT STAND ON
C O M B U S T I B L E
M A T E R I A L S
OR
CARPETS OR BE FITTED TO A
COMBUSTIBLE WALL.
2.10
The minimum height above the top surface
of the hearth for any projection (e.g. shelf
etc.) 150mm deep made from wood or any
other combustible material is 766mm. For
combustible projections above 150mm
depth, add 12.5mm to the above clearance
for every 25mm of additional projection
depth.
2.10.A
HOLE IN THE WALL APPLICATION
The
appliance can be used in a no hearth
application if the installation complies to BS
5871-3:2005 and appliance is installed so
that the height from the base of the fireplace
opening to the floor is no less then 300mm
as shown in Fig 3
2.11
Please note that soft wall coverings (e.g.
embossed vinyl’s etc.) are easily affected by
heat. They may, therefore, scorch or
become discoloured when close to a heating
appliance. Please bear this in mind when
installing.
2.12
The appliance
MUST NOT
be installed in
any room which contains a bath or shower or
where steam is regularly present.
2.13
An extractor fan
MUST NOT
be fitted in the
same room as the appliance or in any area
from which ventilation is taken IF IT IS
LIKLEY TO AFFECT THE
SAFE
OPERATION OF THE APPLIANCE. If there
is a fan in such a locality, note the spillage
test requirements detailed on page 16.
2.14
VENTILATION REQUIREMENTS
For use in
GB
purpose-built ventilation is not
normally required for 600 model. The
1000
model
REQUIRES
ventilation of min air
space 100mm x 100 mm
For use in
I E
ventilation must be in
accordance with IS 813.
2.15
It is essential that all decorative fenders
have a minimum open area of 50cm_ to
ensure adequate air supply for correct
combustion and are approved for use with
this appliance.
3
CHECK CARTON CONTENTS
1 Fire Royal Burner Unit.
1
Set of fuel ceramic pieces
1
Pack of Granular Material
1
Battery pack 6 X AA, 1 X D cell
1
Remote Handset
(
Remote Version Only
).
1
Instruction Manual.
1
Gather hood
1
Fixing kit
0 The adapter to 175mm tube is not
included
4
THE FIREPLACE
4.1
FIREPLACE SIZE
Make sure that the fireplace conforms to
the sizes stated in 2.2 of General
Installation Requirements (refer to Figure
3).
Figure 3
330 (M1000)
310 (M600)
1035 (M1000)
635 (M600)
563 (M600)
622 (M1000)
450 MIN
4.2
The fireplace opening should be in good
order and have a reasonably flat floor level
with the hearth.
4.2
After preparing the fireplace, apply a
lighted match, paper or smoke match to
the chimney opening. Observe the smoke.
If there is a definite flow into the opening,
continue with the installation. If there is not
a definite flow, pre-heat the chimney for a
few minutes and re-check. If there is still
no definite flow, the chimney may need
attention.
DO NOT FIT THE APPLIANCE
– SEEK EXPERT ADVICE.
5
GAS SUPPLY PIPE
A restrictor PTP elbow is provided for the
gas connection
NOTE: The supply pipe must be of rigid durable
material. Flexible pipe MUST NOT be used.
6
APPLIANCE INSTALLATION
6.2
Remove the gather hood this is placed in
the fire box up side down. Remove the
V-11-07
