6
Use only the blades specified for this saw.
Before each use; Ensure that the blade is fully secure.
For your safety; remove the chippings and work debris etc. from the table top and from
inside the extraction port before each operation.
Make sure that all keys and wrenches are removed before switching on the saw.
Keep hands out of path of the saw blade.
Make sure the blade is clear of the workpiece before the switch is turned on.
Allow the saw to run up to full speed before starting a cut.
Stop operation immediately if you notice anything abnormal.
Wait for the saw blade to stop completely and remove from mains supply before ser-
vicing or adjusting the saw.
Be alert at all times, especially during repetitive, monotonous operations. Don't be lulled
into a false sense of security. Blades are extremely unforgiving.
Use of improper accessories may cause damage to the saw and surrounding area as
well as increasing the risk of injury.
Do not modify the saw to do tasks other than those intended.
Do not cut workpieces too small to hold by hand outside the blade guard.
Maintain a steady grip, avoid awkward positions and do not allow your hand to be in
direct line of the cut.
Make sure the blade is installed with the teeth pointing downward at the front of the saw
to avoid lifting of the workpiece.
Hold the workpiece firmly against the table.
Do not feed the work too quickly while cutting, only feed at a rate so that the blade
can perform the cut without overloading the saw.
Be very cautious when cutting material of uneven cross section such as mouldings,
ensure the material is laying flat and firmly on the table.
This table saw is for indoor use only.
Clear the work table of all objects (tools, scraps, rulers etc.) except the workpiece be-
fore turning the saw on.
When cutting a large piece of material, support it at the height of the table with rollers
or similar.
Make sure there are no nails or foreign objects in the part of the workpiece to be sawn.
Use the push stick to the side of the blade line to push the workpiece securely through
SAFETY INSTRUCTIONS...cont
designed.
DO NOT OPERATE THE SAW IN EXPLOSIVE ATMOSPHERES:
Do not use the saw in the pres-
ence of flammable liquids, gases, dust or other combustible sources. The saw may create
sparks which can ignite the dust or fumes.
DO NOT EXPOSE THE SAW TO RAIN OR USE IT IN WET CONDITIONS:
Water entering the saw
will greatly increase the risk of electric shock.
WARNING:
The dust generated by certain wood or wood derived products can be danger-
ous to the operator, as well as anyone in the area. Always operate The saw in well ventilat-
ed areas and provide dust removal where possible.
23
Ref. No.
Description
SIP Part No.
Ref. No.
Description
SIP Part No.
1.
Table Insert
WD01-01078
36.
Brush Holder
WD01-01113
2.
Screw
WD01-01079
37.
Carbon Brush
WD01-01075
3.
Screw
WD01-01080
38.
Screw
WD01-01114
4.
Table
WD01-01081
39.
Spring Washer
WD01-01115
5.
Nut
WD01-01082
40.
Washer
WD01-01116
6.
Carriage Bolt
WD01-01083
41.
Motor House
WD01-01117
7.
Chain Bar
WD01-01084
42.
Strain Relief
WD01-01118
8.
Scale
WD01-01085
43.
Motor Connect Line
WD01-01119
9.
C-ring
WD01-01086
44.
Bearing Sleeve
WD01-01120
10.
Bevel Shaft
WD01-01087
45.
Bearing
WD01-01121
11.
Bevel Shaft Support
WD01-01088
46.
Motor Housing Field Assembly
WD01-01122
12.
Press Plate
WD01-01089
47.
Self Tapping Screw
WD01-01123
13.
Pin
WD01-01090
48.
Armature Assembly
WD01-01124
14.
End Cap
WD01-01091
49.
Bearing
WD01-01125
15.
Socket Screw
WD01-01092
50.
Baffle
WD01-01126
16.
Wing Nut
WD01-01093
51.
Gear Housing
WD01-01127
17.
Parallel Stop
WD01-01094
52.
C-ring
WD01-01128
18.
Carriage Bolt
WD01-01095
53.
Gear
WD01-01129
19.
Stop Rail
WD01-01096
54.
Screw
WD01-01130
20.
Self Tapping Screw
WD01-01097
55.
Bearing
WD01-01131
21.
Rip Fence Indicator
WD01-01098
56.
Bearing Cover Plate
WD01-01132
22.
Parallel Stop
WD01-01099
57.
Arbor
WD01-01133
23.
Eccentric Lever
WD01-01100
58.
Flat key
WD01-01134
24.
End Cap
WD01-01101
59.
Spring Washer
WD01-01135
25.
Mitre Gauge Stop Rail
WD01-01102
60.
Screw
WD01-01136
26.
Carriage Bolt
WD01-01103
61.
Motor Bracket
WD01-01137
27.
Self Tapping Screw
WD01-01104
62.
Lower Blade Guard
WD01-01138
28.
Mitre Handle
WD01-01105
63.
Inner Blade Flange
WD01-01139
29.
Mitre Gauge
WD01-01106
64.
Washer
WD01-01140
30.
Self Tapping Screw
WD01-01107
65.
Blade
WD01-01141
31.
Mitre Gauge Indicator
WD01-01108
66.
Outer Blade Flange
WD01-01142
32.
Rod - Mitre Gauge
WD01-01109
67.
Hex. Bolt (L)
WD01-01143
33.
Hex bolt
WD01-01110
68.
Dust Chute
WD01-01144
34.
Motor End Cap
WD01-01111
69.
Screw
WD01-01145
35.
Self Tapping Screw
WD01-01112
70.
Extraction Hose
WD01-01146
PARTS LIST
