sinmag GF-18 Owner'S Manual Download Page 16 | Manualshive

Page: 16 / 16

background image

MACHINE WARRANTY

15

Machine Warranty

We promise to offer our clients the best quality of products and service, our

guaranty period is one year dated from the delivery date.

The following terms are not included:

1. Abnormal operation or adjustment.

2. Sundries or corrosive liquid or wasted oil enter to cylinder make short

circuit and burnt out of internal components.

3. Damage caused by hard matter impact.

4. Disasters caused by nature reasons.

«
...
14
15
16

Summary of Contents for GF-18

















Reviews:

No comments

Related manuals for GF-18

Spacemaker WSM2700L

Brand: GE Pages: 28

Silhouette DBC031D4BSSPR

Brand: Danby Pages: 26

Brand: Faber Pages: 10

Brand: SALCO Pages: 23

Brand: Monogram Pages: 20

Brand: MAM Pages: 29

Brand: YATO Pages: 48

Brand: Aroma Professional Pages: 20

Brand: Bestron Pages: 28

Brand: Royal Catering Pages: 5

Brand: DEJELIN Pages: 72

Brand: GRAZIANO Pages: 7

Brand: ZAKARIAN Pages: 15

Brand: Hamilton Beach Pages: 80

Brand: FoodSaver Pages: 20

Brand: Bestron Pages: 28

Brand: Sammic Pages: 36

Brand: Qi Aerista Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands