Explanation of the NOVAMIG 320 LCD plate
Pos. 1
Name and address of the manufacturer
and trademark
Pos. 2
Identification of the welding machine model
Pos. 3
Welding machine serial number
Pos. 4
Welding machine type symbol: Transform-
er - Rectifier for arc welding
Pos. 5
Reference to the legislation followed for
welding machine construction: EN 60974-1
Pos. 6
Welding with MIG/MAG procedure
Pos. 6a Welding with TIG procedure
Pos. 6b Welding with MMA procedure
Pos. 7
Symbol indicating that the welding ma-
chine can be used in environments with
an increased risk of electric shock
Pos. 8
Welding current symbol: Direct Current /
Alternating Current
Pos. 9
Rated no-load voltage U0 in V
Pos. 10 Electric adjustment range of the welding ma-
chine: minimum and maximum rated welding
current, with the relevant charged voltages
Pos. 11 Welding machine service factor (X): this
figure indicates the welding machine ser-
vice factor as a percentage of a 10-minute
work cycle. Example X = 60% - I2 350 A,
these data indicate that the welding ma-
chine on a work cycle can weld with a cur-
rent I2 = 350 A for a time of 6 minutes out
of 10, that is 60%.
Pos. 11a Service factor: 40 %
Pos. 11b Service factor: 60 %
Pos. 11c Service factor: 100 %
Pos. 12 Rated welding current (I2)
Pos. 12a Value of the rated welding current at 40%
Pos. 12b Value of rated welding current at 60%
Pos. 12c Value of rated welding current at 100%
Pos. 13 Conventional load voltage (U2)
Pos. 13a Voltage at 40 % load
Pos. 13b Voltage at 60 % load
Pos. 13c Voltage at 100 % load
Pos. 14 Symbol for the welding machine power
supply and number of phases followed by
the direct/alternating current symbol
Pos. 15 Insulation class
Pos. 16 Rated power voltage
Pos. 17 Maximum current in MIG welding
Pos. 18 Actual current in MIG welding
Pos. 19 Indicates the degree of welding machine
protection: IP 23
Pos. 20 Product complies with the safety require-
ments established by the applicable EU
directives or regulations
Pos. 21 See chapter 9.
ADDITIONAL INSTRUCTIONS
2. GENERAL INFORMATION
2.1. MANUFACTURER
IDENTIFICATION DATA
MANUFACTURER: SINCOSALD S.r.l
HEADQUARTERS - OFFICES
via della Fisica, 26/28
20864 Agrate Brianza (MB) Italy
Tel: +39 039 641171
Fax: +39 039 6057122
CONTACTS:
[email protected] www.sincosald.it
2.2. MACHINE IDENTIFICATION
DATA AND PLATES
Each machine is identified by a CE plate on which its
reference data is indelibly marked. For any commu-
nication with the manufacturer or service centre al-
ways quote these references.
IMPORTANT: The plate must not be removed for
any reason, under penalty of forfeiture of the
guarantee and the unavailability of spare parts
due to failure to be identified. The position of the
nameplate on the Machine can vary from machine
to machine.
NOVAMIG 320 LCD plate
EN 60974 - 1
X
100 %
I2
199 A
U2
24 V
Uo
55 V
1 ~ 50/60 Hz.
U1 = 400 V
I1max = 20 A
I1eff = 12.6 A
IP 23
CL = H
40 %
315 A
29.8 V
Uo
55 V
Uo
55 V
NOVAMIG 320 LCD
X
I2
U2
22.6 V
315 A
40 %
18 V
199 A
100 %
X
I2
U2
32.6 V
315 A
40 %
28 V
100 A
100 %
60 %
257 A
26.9 V
60 %
257 A
20.3 V
60 %
130 A
30.3 V
10A - 16 V / 315A - 29.8 V
3
3
10A - 10.4 V / 315A - 22.6 V
10A - 20.4 V / 315A - 32.6 V
1
2
3
5
6
8
8
8
7
7
7
14
19
16
17
21
9
9
9
10
10
10
11
11
11
12
12
12
13
13
13
11a
12a
13a
11a
11a
12a
12a
13a
13a
11b
12b
13b
11b
11b
12b
12b
13b
13b
11c
12c
13c
11c
11c
12c
12c
13c
13c
4
6a
6b
20
15
18
1.995.234 EN - Rev. 1.1
NOVAMIG 320 LCD
6