Sinclair S-THERM GSH-100ERB Service And Installation Manual Download Page 67 | Manualshive

Page: 67 / 153

Sinclair S-THERM GSH-100ERB Service And Installation Manual Download Page 67

Control

Page 60 Total 145

3.2.4.2 2-Way valve

[Operation Instructions]

★

At the commissioning parameter setting page, by touching “

Cool 2-Way valve

” or “

Heat 2-Way

valve

”, the control panel will access to the corresponding setting page.

[Notes]
●Under “

Cool

”, or “

Cool + Hot water

” mode, “

Cool 2-Way valve

” will decide the status of the 2-way

valve; while under “

Heat

” or “

Heat + Hot water

”, “

Heat 2-Way valve

” will decide the status of the 2-way

valve.
●It will be memorized upon power failure.

3.2.4.3 Solar Setting

[Operation Instructions]

★

1. At the commissioning parameter setting page, by touching “

Solar setting

”, the control panel will

access to its submenu page.

★

2. At the submenu page, “

Solar setting

” can be set to “

With

” or “

Without

”.

★

3. At the submenu page, the “

Solar heater

” can be set to “

On

” or “

Off

”.

Solar Setting

[Notes]
●This setting can be done no matter if the unit is turned on or off.
●This setting is allowed only when the water tank is available. When the water tank is unavailable, this
setting will be reserved.
●It will be memorized upon power failure.

3.2.4.4 Water Tank

[Operation Instructions]

★

At the commissioning parameter setting page, by touching “

Water tank

”, the control panel will

access to the corresponding setting page, where “

Water tank

” can be set to “

With

” or “

Without

”.

[Notes]
●This setting will be memorized upon power failure.
●This setting will become valid only when the unit is turned off.

3.2.4.5 Thermostat

[Operation Instructions]

★

1. At the commissioning parameter setting page, by touching “

Thermostat

”, the control panel will

access to the corresponding setting page.

★

2. At the

“

Thermostat

” setting page, it can be set to “

Air

”, “

Without

” or “

Air + hot water

”. When it is

set to “

Air

” or “

Air + hot water

”, the unit will run based on the mode set by the thermostat; when it

is set to “

Without

”, the unit will run based on the mode set by the control panel.

«
...
65
66
67
68
69
...
»

Summary of Contents for S-THERM GSH-100ERB


























































































































































Reviews:

No comments