background image

IQ-SA-360-FM 251012:IQ-SA-360-CS-W.qxd  10/26/12  5:40 PM  Page 3 

 

 

 

  

 

 

 

In this warranty: 
We means Simx;

 

You means the consumer of the Goods

 

 

Supplier means the authorised distributor or retailer that sold you the Goods in New Zealand 

or Australia; and

 

Goods means the Simx product accompanied by this warranty and purchased in New Zealand 

or Australia.

 

The benefits provided to you under the following warranty are in addition to any other rights 

and remedies available to you under the law:

 

1.  If, during the time from the date of purchase (Warranty Period), there is a defect in the 

Goods due to improper workmanship or material, we will replace or repair the Goods 

without charge. Any replacement product is warranted only for the time remaining on the 

original Warranty Period.

 

 

2.  We are not obliged to replace or repair the Goods under clause 1 if the Goods have been 

improperly stored, installed, connected, used, operated, repaired, damaged, abused, 

tampered with, altered (without our written approval), or not maintained in accordance with 

our recommended installation, connection and operating instructions.

 

 

3.  The warranty provided under clause 1 is limited to replacement or repair of the Goods only, 

at our option. To the extent permitted by law, we exclude liability for:

 

 

a) consequential loss or any other loss or damage caused to property or persons 
arising from any cause whatsoever;

 

b) damage to consumable items such as lamps and starters; and

 

c) damage arising from normal wear and tear.

 

4.  In order to claim under this warranty you must, within the Warranty Period, return the Goods 

to the Supplier, together with the original proof of purchase including the details below:

 

 

Supplier                                                              Name 

 

 

 Date 

Of                                                      

Purchase        

 Model Number 

 

 

 Invoice/Receipt  No.      

 

 

5.  This warranty does not cover the cost of claiming under the warranty or transporting the 

Goods to and from the Supplier.

 

 

Our Goods come with guarantees that cannot be excluded under the Australian Consumer 

Law. You are entitled to a replacement or refund for a major failure and for compensation for 

any other reasonably foreseeable loss or damage. You are also entitled to have the Goods 

repaired or replaced if the Goods fail to be of acceptable quality and the failure does not 

amount to a major failure.

 

SIMX WARRANTY INFORMATION

 

This product is suitable for use only with a supply voltage of 230-240V AC 50Hz. 

All electrical work must be carried out in accordance with local and national 
electrical codes as applicable. We strongly recommend that thissensor is installed 
by a registered electrician.

Always switch power off prior to installation. A means of mains power isolation 
must be installed on the circuit for the purpose of safe access for any internal 
cleaning, recalibration, or maintenance.

This sensor is not intended for use by persons (including children) with reduced 
physical, sensory or mental capabilities, or lack of experience and knowledge, 
unless they have been given supervision or instruction concerning use of the 
appliance by a person responsible for their safety. Young children should be 
supervised to ensure that they do not play with the appliance.

Any changes or modifications made or attempted to this product, without the  
prior written approval of the manufacturer, will void any and all stated warranties. 

This product is guaranteed by SIMX Ltd for 36 MONTHS from the date of 
purchase against faulty materials or workmanship which affects its designed 
ability to switch or operate. During this period if the product has a defect of 
this nature it will be repaired or replaced free of charge by SIMX with the same 
item, or a similar one of higher specification. ON CONDITION THAT:

The buyer returns it to the seller from whom it was bought, freight paid.

The product has been bought by the user. ie a receipt/sales invoice is 
produced as proof of purchase the product has not been misused or handle 
carelessly, installed in anyway contrary to the installation instructions, or 
installed in any unusually exposed or harsh environmental conditions.

This guarantee excludes liability for discolouration of paint or plastic, or any user 
replaceable parts.It does not conferany rights other than those expressly set 
out above and does not cover any claims for consequential loss or damage.

Our Goods come with guarantees that cannot be excluded under the Australian 
and New Zealand Consumer Law. You are entitled to a replacement or refund for 
a major failure and for compensation for any other reasonably foreseeable loss or 
damage. You are also entitled to have the Goods repaired or replaced if the Goods 
fail to be of acceptable quality and the failure does not amount to a major failure.

Summary of Contents for LHT0142











Reviews: