background image

IQ-SA-360-FM 251012:IQ-SA-360-CS-W.qxd  10/26/12  5:40 PM  Page 10 

 

 

 

SECTION FIVE

  

TECHNICAL SPECIFICATIONS

 

 

Detection Range

 

Detection Angle

 

Power Supply

 

Maximum Switchable Load

 

 

 

 

Time On Adjustment

 

Dusk Level Adjustment

 

Environmental Protection

 

Up to 6 metres diameter (3m Radius) at mounting

 

height of 2.5m

 

360º

 

 

230 V AC ~ 50Hz

 

 

2000W (20 x 100W GLS) Incandescent

 

500W Fluorescent

 

200W (inductive load, cosѲ = 0.2)

 

seconds - 15 minutes

 

Day & night or night only operation

 

IP44 

(suitable for sheltered outdoor use)

 

 

  

 

 

 

 

 

 

 

 

 

 

 

 

If you experience problems refer to Troubleshooting Guide.

 

If problems still exist, do not immediately return the unit to store.

 

 

Telephone the Simx Customer Helpline

 

NZL:  64 9 259 1662

 

Weekdays 9.00am – 5.00pm

 

Email: [email protected]

 

Website: www.simx.co.nz

 

 

Qualified Customer Support Co-ordinators will be on-line to assist in resolving your query.

 

5 seconds - 15 minutes

Product Complies with:

EN 60669-2-1:2004, EN 60669-1:1999+A1:2002

Distributed by:

 Simx Limited 

Ph: +64 9 259 1660 | Technical Support Ph: +64 9 259 1662 
Email: [email protected] | www.simx.co.nz

Simx reserves the right to alter technical specifications without prior warning 

300W LED

Summary of Contents for LHT0142











Reviews: