*8&9: N. C. Reversing Sensor
10&11: Remote Override Switch (SPBS)
12: Coax Antenna Connection (not supplied)
13: Standard Antenna (supplied with unit)
* NOTE: If you are not using a safety device a
jumper wire must be connected to
terminals 8 & 9.
Do not cut antenna wire supplied with this unit.
RC200 Receiver
PW
POWER IN 120VAC
HOT
NEUTRAL
GROUND
Antenna
*JUMPER
M
N.O. SINGLE POLE
SINGLE THROW SWITCH
(REF#SPBS)
GREEN
RED
WHITE
BLACK
LD
12
CODE
MEMOR
Y
8
9
10 11
12
13
1
2
3
4
5
6
7
SW1
P1
P2
MEMO
DELETE
ON
A
B
C
EXTERNAL DIMENSIONS
BATTERY REPLACEMENT
SETTING THE TRANSMITTER CODE
WIRING DIAGRAM (fig. 9)
A: Entry holes for 120VAC
B: Entry holes for low voltage wiring and antenna
D: Hole plugs
PW: Power light
SW : Function selection switch
P1: Memorize button
LD: Signal LED
P2: Delete button
1: Ground (Green)
2: Ground (Green)
3: Hot 120VAC
4: Neutral
5: Direction 1 ( Black )
6: Direction 2 (Red)
7: Common (White)
1
2
N
O
1
2
N
O
1
2
N
O
1
2
N
O
PROGRAMMING
SETTING CODES IN THE TRANSMITTERS (Fig. 1-6)
MEMORIZING TRANSMITTER CODES WITH THE RECEIVER
1) Open the access door (Fig. 1)
2) (Only on 12 channel transmitter) Select block of channels
with ABC slide switch Y1 (Fig.2)
Y1 in position A = channels 1-4
Y1 in position B = channels 5-8
Y1 in position C = channels 9-12
3) Press button J1 (Fig3)
4) While holding down button J1, press one of the transmitter
buttons CH and the light L1 will start flashing (Fig 4.)
5) Release the transmitter button CH and the light L1 will
continue flashing (Fig5)
6) Release the button J1 and the light will go out (Fig 6) That
transmitter button CH now has its code programmed.
7) Repeat steps 3-4-5-6 for each of the buttons CH on the
transmitter.
8) If using a 12 channel transmitter (4 buttons CH and ABC
slide switch Y1), repeat steps 2-3-4-5-6-7 with the slide
switch Y1 in each position. (A-B-C)
IMPORTANT: It is recommended for the receiver memory
to be cleared before memorizing transmitter codes for
the first time. Press buttons P1 and P2 simultaneously for
5 seconds until led LD flashes rapidly.
Dipswitch SW1 functions
(Fig. 9)
DIP1 ON / DIP2 ON
Memorized code control in sequencing function.
OPEN-STOP-CLOSE-STOP-OPEN.....
DIP1 OFF / DIP2 OFF
Run time programming
DIP1 ON / DIP2 OFF
Memorized code will give up command
DIP1 OFF / DIP2 ON
Memorized code will give down command
1) Using SW1 select the function to be associated with that
button on the transmitter. (ON/ON) Is standard for individual
control.
2) Press button P1 and the LED labeled LD will start to flash
3) While holding down button P1, bring the transmitter within 6
inches of the receiver and press the transmitter button CH
you wish the receiver to memorize. The LED LD will flash faster
4) Release the transmitter button CH and the receiver button
P1. The receiver has memorized the code for that button on
the transmitter.
5) Repeat steps 1-2-3-4 for all other transmitter buttons you
wish the receiver to memorize.
6) When finished programming the receiver move both
dipswitches on SW1 to the off position.
* If the receiver will not memorize a code it could be due to:
- The memory is full (24 codes memorized) and led LD
remains lit. If this is the case, a new code can be
memorized only after one is erased or the whole memory
is cleared. (See “ERASING RECEIVER MEMORY BELOW)
- The code is already in memory
- You have not generated a code for that transmitter button.
(See “SETTING CODES IN TRANSMITTERS” ABOVE)
To erase a single transmitter button code from receiver memory
1) Press and hold button P2 and the led LD will flash slowly
2) Press the button of the receiver you wish to erase and hold
for 3 seconds until led LD flashes faster. The code is erased.
3) Repeat steps 1 and 2 for each button on all receivers you
want to erase from the receiver’s memory.
To erase the entire memory of a receiver
1) press and hold buttons P1 and P2 for at least 5 seconds
until led LD flashes rapidly. The whole memory is cleared.
ERASING RECEIVER MEMORY
CH1
CH3
CH2
CH4
Run time programming (SW1)
- move the door/shutter to the completely closed position;
- press and hold down the MEMO button for 4 seconds:
release the button when the LED starts to flash;
- press the MEMO button once, within 10 s, to start the
opening manoeuvre; when the door/shutter has stopped in the
completely open position, wait for 2-3 seconds and then press
the button again to memorise the run time; this completes
the program function and the LED will switch off;
NOTE: during programming the photoelectric cells are ignored
and the LED will flash rapidly indicating that the run time is being
counted.
• The maximum programmable run time is
120 seconds
.
F1 - 4.0 A
ZVL408.01-P2 Mod: 18-04-2008
Summary of Contents for (X) 200 TRAN202
Page 3: ......
