![background image](http://html.mh-extra.com/html/simu/x-200-tran202/x-200-tran202_manual_1279436004.webp)
PAGE: 2 of 2
A
A
B
B
C
C
D
D
E
E
F
F
CDR 863 with SMC
CDR 863 with SMC
”
1.5
”
1.5
.5
”
3
4
.5
”
3
4
1.9
6”
1.9
6”
1
3
2
A: Mounting Gasket
B: Base Plate
C: Cover Gasket
D: Adjustable Optic
E: Control Board
F: Cover with Optic Window
ASSEMBLY
Test Point
+
_
1
1
2
2
3
3
4
4
5
5
6
6
24V
+
12V
+
0V
-
NC NO COM
~
~
~
Receiver
1
1
2
2
3
3
4
4
24V
+
12V
+
0V
-
~
~
~
0V
-
~
Emitter
1
1
2
2
3
3
4
4
5
5
6
6
24V +
12V +
0V -
NC
NO
COM
~
~
~
C
NC
NO
C
NO
NC
18
0
+
3
0
-3
0
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
DIMENSIONS
CONNECTIONS
TEST POINT
ALIGNMENT
Description
The CDR863 is an outdoor/indoor photoelectric beam and can be used with
the SMC to control a tubular motor covering passage way up to 30’ outdoors
and 45’ indoors.
Mounting
(Fig. 1)
1) Using the template on the lid of the box, mark the position of the transmitter
and receiver and install gasket (A) and the mounting plate (B) in the desired
locations using the four #6 flat head wood screws. When mounting to other
than wood surfaces use the appropriate anchors.
2) Run the wires through the hole in the gasket and mounting plate and into
the unit.
Wiring and Calibration
WARNING: DO NOT APPLY POWER UNTIL ALL CONNECTIONS HAVE BEEN MADE!
1) Connect wires as shown on page one of this addendum.
2) Power the units. The red LED on the transmitter will light. The red LED on the
receiver will light only if the optic eyes are not aligned
3) Align the eyes using a DC voltage meter on the test point (Fig. 4). The meter
should read 0.9V or higher when aligned.
4) Seal the wire holes using the supplied rubber plugs. Install the cover and
secure with supplied screws (Fig. 1 a,b,c)
5) Test the function. Note: If the eye causes the door to lower instead of raise,
reverse the red and black motor leads.
Technical Specifications
Optical
Range: (outdoors)
up to 30 ft.
(indoors)
up to 45 ft.
Transmitter beam width:
6 degrees (typical)
Receiver field of view:
6 degrees (typical)
Adjustment Vertical:
+/- 30 degrees
Horizontal:
180 degrees
Electrical
Voltage:
12 or 24 VAC/VDC _ 10%
Current consumption @ 12V: 23mA (rest) 65mA (active)
Current consumption @ 24V: 29mA (rest) 68mA (active)
Relay:
Form C (Com, NO, NC)
Relay drop out with loss of power
Contacts rated 60VA @ 24VDC/VAC
Max 30VDC/VDC
Infrared source:
Double Gallium Arsenide LEDs
Transmitter frequency:
4.7 kHz
IR wavelength:
950 nm
Environmental
Operating temperature:
14 to 131 degrees F (-10 to +55 degrees C)
+
APPENDIX 2
Summary of Contents for (X) 200 TRAN202
Page 3: ......