background image

BSM-2 Installation manual | 7

E

NG

L

IS

H

Installation and wiring

Mounting location

Before installing the BSM-2, consider location and cable 

runs necessary to connect the module to display unit, 

transducer and power source.

The mounting location must allow for required working 

area when connecting the cables. Also ensure that the 

location allows viewing the unit’s LED indicators.

The units should be mounted with special regard to the 

units’ environmental protection, temperature range and 

cable length.

The mounting surface needs to be structurally strong, 

with as little vibration as possible. If possible mount the 

unit close to the edges of a panel to minimize vibration.

Do not run the transducer cabling near the BSM-2 power 

cables, any VHF antenna coax cables or any DC or AC 

power cables. Avoid placing Ethernet cables close to VHF 

antennas.

The BSM-2 conforms to the appropriate Electromagnetic 

Compatibility (EMC) standards, but proper installation 

is required to get best use and performance from 

this product. Ensure you have as much separation as 

possible between different electrical equipment, (see 

diagram below). 

X

X

Electromagnetic interference

Gasoline fumes

Vibration

Heat

Sunlight

Salt spray

Physical damage

2.0 m (6.5 ft) Min

1.8 m (6 ft) Min

1.5  m (5 ft) Min

RADAR

Radio or AIS Transmitter

Compass

Summary of Contents for BSM-2


























Reviews: